New Holland FR450 TIER 3 Page 74 Service Manual Download

Page: 74 / 81

Engine - Engine and crankcase

73. Refill the earlier drained hydraulic oil into the hydraulic

oil reservoir

(18)

. Top up as necessary. Refer to the

Operator's Manual

Oil filter - Replace (29.204)

NOTE:

On the right-hand side under the machine, ensure

the indicated drain plug on the fuel tank is fully tightened.

74. Refill the earlier drained fuel. Refer to the Operator's

Manual

Fuel tank - Check (10.216)

ZEIL13FR00346AB

75. Manually move the spout to its home position.

76. Tighten the nut

(12)

, until the worm

(14)

is on the worm

wheel

(15)

77. Adjust the backlash between the worm and the worm

wheel.

Refer to

Worm/Worm wheel - Backlash

(70.140)

78. Tighten the lock nut

(13)

79. Calibrate the spout home position. Refer to the Oper-

ator's Manual.

ZEIL07FR0417A0Z

80.

Reinstall the rear shielding

(3)

as follows:

A. Lift the rear shielding

(3)

and position it on the

machine. Use a suitable lifting device.

B. Install the hardware

(7)

C. Install the plate

(6)

D. Install the gas strut

(4)

on the rear shielding

(3)

ZEIL11FR0029A0B

81. Install the steering wheels. Refer to

Rear wheel -

Install – Steering wheels (44.520)

47812470 23/02/2015

10.1 [10.001] / 37

Summary of Contents for FR450 TIER 3


















































































Search results

Summary of Contents for FR450 TIER 3

Reviews:

Related manuals for FR450 TIER 3

Brands by name

Popular brands

New Holland FR450 TIER 3, Service Manual

Search results

Summary of Contents for FR450 TIER 3

Reviews:

Related manuals for FR450 TIER 3

Brands by name

Popular brands