background image

- 1 - 

1. Introduction 

 

Thank you for purchasing the New Cosmos KS-7R carbon dioxide detector. 
 
To ensure safe and reliable operation, please read this instruction manual prior to use. 
 
This unit detects carbon dioxide and is intended for use in a non-hazardous indoor area, e.g. office, 
laboratory, or clean room, for the early detection of a gas leak.   
The  unit  will  relay  the  gas  concentration  value  as  an  analog  signal  (4-20mADC)  to  external 
equipment while simultaneously displaying the gas concentration value on its display. 
 
This unit monitors carbon dioxide levels, and when they reach a preset level, the unit will produce 

audio-visual alarms and activate relay contacts. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 

 

This manual uses Danger, Warning, Caution and Note symbols to draw attention to 

procedures, materials, methods, and processes, which require particular attention. 

:  Indicates  an  imminently  hazardous  situation  that  can  result  in 

death or serious injury. 

: Indicates a potentially hazardous situation that may result in death 

or serious injury. 

:  Indicates  a  hazardous  situation  that may  result  in  minor  injury  or 

property damage. 

: Provides information on product handling. 

DANGER

 

CAUTION

 

WARNING

 

NOTE 

Summary of Contents for KS-7R









































Reviews: