background image

 

chloride  and  1,1,1 Trichloroethane 
They are not compatible with aluminum and 
may cause an explosion. If you are unsure of 
a material’s compatibility with aluminum, 
contact your coating supplier. 

 

GENERAL SAFETY WARNINGS 

Warning! Hazardous vapors. 

Spray materials, solvents, and 

other materials can be harmful if 

inhaled or come in contact with the body. Vapors 

can cause severe nausea, fainting, or poisoning.

 

 

To avoid these risks, take the following 
preventions: 

•  Use a respirator or mask if vapors can be 
inhaled. Read all instructions supplied with the 
mask to be sure it will provide the necessary 
protection. 
•  Wear protective eyewear. 
•  Wear  protective  clothing  as  required  by 
coating manufacturer.

 

 

Warning! Electric shock 

hazard. 

May cause severe injury. 

 

To avoid these risks, take the following 
preventions 

•  Keep electrical cord plug and sprayer 
trigger free from spray material and other 
liquids. Never hold cord at plug connections 
to support cord. Failure to observe may result 
in an electrical shock 
•  Never immerse electrical parts in water or 
any other liquid. Wipe the exterior of the 
sprayer with a damp cloth for cleaning. 
Always make sure the sprayer is unplugged 
before taking it apart for cleaning. 
•  Do not expose unit to rain or wet 
conditions. 
•  Do not abuse the cord. Never use the 
cord to carry the unit or pull the plug from an 
outlet. Keep cord away from heat, oil, sharp 
edges or moving parts. 
•   Replace damaged cords immediately.

  

 

Warning! General. 

To reduce the risk 

of severe injury or property damage. 

To avoid these risks, take the following 

preventions:

 

•  Do not aim the gun at, or spray any 
person, including self, or animal. 
•  Do not spray outdoors on windy days 
•  Wear protective clothing to keep spray 
material off skin and hair. 
•  Hose may become hot and cause skin 
burn. 
•  Follow all appropriate local, state, and 
national codes governing ventilation, fire 
prevention, and operation. 
•  Always use appropriate gloves, eye 
protection and a respirator or mask when 
spraying, thinning, mixing, pouring, or 
cleaning. 
•  Do not operate or spray near children. 
Keep children away from equipment at all 
times. Keep sprayer out of the reach of 
children. 
•  Do not overreach or stand on an unstable 
support. Keep effective footing and balance at 
all times. 
•  Stay alert and watch what you are doing. 
Do not operate the unit when fatigued or under 
the influence of drugs or alcohol. 
•  Read all instructions and safety precautions 
for equipment and spray material before 
operating any equipment. 
•  Hearing protection is recommended 
for extended use. 
 

ELECTRICAL SAFETY

 

This tool is double insulated, therefore 
no earth wire is required. Always 

check that the power supply corresponds to 
the voltage on the rating plate. 
•  If the supply cord is damaged, it must be 
replaced by the manufacturer or an 
authorized Service Centre in order to avoid a 
hazard. 
•  When using the tool outdoors, only use 

Summary of Contents for NSG0110-US500













Reviews: