Network Equipment Technologies SBC 2000 Manual Download Page 9

Various national agencies (in the United States, the Federal Communications Commission (FCC)) govern the levels of electromagnetic emissions from
digital devices. Electromagnetic emissions can interfere with radio and television transmission. To reduce the risk of harmful interference these agencies
have established requirements for manufacturers of digital devices.

The manufacturer of a digital device must test and label a product to inform an end-user of the maximum emission level from the product when used in
accordance with its instructions. The emissions levels encountered are classified as Class A or Class B. A system that meets the Class A requirements
can be marketed for use in an industrial or commercial area. A system that meets the more stringent Class B requirement can be marketed for use in a
residential area in addition to an industrial or a commercial area.

The end user is generally held responsible for ensuring that the system is suitable for its environment as stated in the above paragraph, and bears the
financial responsibility for correcting any harmful interference.

Modifications

Modifications or changes made to this device, and not approved by Network Equipment Technologies, may void the authority granted by the FCC, or other
such agency, to operate this equipment.

Federal Communications Commission Notice

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.This equipment
generates, uses, and can create radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area can cause harmful interference in which case the user will be
required to correct the interference at the user's expense.

Canadian Notice

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of
Industry Canada.

Avis Canadien

Cet appareil numérique n'émet pas de bruits radioélectriques depassant les limites applicables aux appareils numériques de la Classe A prescrites dans
le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada.

Product Disposal

Ensure that you use proper methods for disposal of any UX equipment. Your disposal methods should be conducted in accordance with all national laws
and regulations.

Ultimate disposal of this product should be handled according to all national laws and regulations.

Dit produkt dient volgens alle landelijke wetten en voorschriften te worden afgedankt.

Tämän tuotteen lopullisesta hävittämisestä tulee huolehtia kaikkia valtakunnallisia lakeja ja säännöksiä noudattaen.

La mise au rebut définitive de ce produit doit être effectuée conformément à toutes les lois et réglementations en vigueur.

Dieses Produkt muß den geltenden Gesetzen und Vorschriften entsprechend entsorgt werden.

L'eliminazione finale di questo prodotto deve essere eseguita osservando le normative italiane vigenti in materia.

Summary of Contents for SBC 2000







































Reviews: