background image

ADC-SDI-CC  

 

   

Rev. 3

 

DATE: 23 July 2008 

 

 

 

                                                   

Network Electronics AS, P.O.Box 1020, N-3204 Sandefjord, Norway. Tel.: +47 33 48 99 99 – Fax: +47 33 48 99 98 
E-mail: [email protected] – Web: http://www.network-electronics.com/ 
 
Technical specifications are subject to be changed without notice. 

 

 

20

 

 

EC Declaration of Conformity 

 

 

 

 

 

 

 

 

 

 

MANUFACTURER 

Network Electronics AS 
P.B. 1020, N-3204 SANDEFJORD, Norway 

AUTHORISED REPRESENTATIVE 
(Established within the EEA) 

Not applicable 

MODEL NUMBER(S) 

ADC-SDI-CC 

DESCRIPTION 

Component and Composite Analogue Video Converter 

DIRECTIVES this equipment complies with 

LVD 73/23/EEC 
EMC 2004/108/EEC 

HARMONISED STANDARDS applied in order to 
verify compliance with Directive(s) 

EN 55103-1:1996 
EN 55103-2:1996 

TEST REPORTS ISSUED BY 

Notified/Competent Body  

Report no: 

 

Nemko E07379.00 

TECHNICAL CONSTRUCTION FILE NO 

Not applicable 

YEAR WHICH THE CE-MARK WAS AFFIXED 

2008 

TEST AUTHORIZED SIGNATORY 

 

MANUFACTURER AUTHORISED 

REPRESENTATIVE 

(Established within EEA) 

Date of Issue 

  

2008-07-14 

 

Place of Issue 

 

Not applicable 

Sandefjord, Norway 

Name  

Thomas Øhrbom 

 

Position 

Quality Manager 
(authorised signature) 

 

 

Summary of Contents for ADC-SDI-CC





















Reviews: