background image

 

 

11 

8. Important Maintenance Instruction 

Kindly pay attention to the following in order to achieve the best maintenance of the product: 

 

• Keep the device dry. Rain, moisture or any liquid might contain minerals and thus corrode electronic circuits. If the device gets 

wet, please dry it completely. 

• Do not use or store the device in dusty or dirty environment. It might damage its detachable parts and electronic components. 

• Do not store the device under excessive heat condition. High temperature can shorten the life of electronic devices, destroy 

batteries, and deform or melt some plastic parts. 

• Do not store the device in places that are too cold. Otherwise, when the temperature rises to normal temperature, moisture will 

form inside, which will destroy the board. 

• Do not throw, knock or shake the device. Rough handling of equipment can destroy internal circuit boards and delicate 

structures. 

• Do not clean the device with strong chemicals, detergents or strong detergents. 

• Do not apply the device with paint. Smudges might block in the device and affect the operation. 

• Do not throw the battery into the fire, or the battery will explode. Damaged batteries may also explode. 

 

All of the above applies to your device, battery and accessories. If any device is not working properly, please take it to the nearest 

authorized service facility for repair. 

 

 

 

 

Summary of Contents for R72615A













Reviews: