background image

 

 

1.

 

Introduction   

 

R72615A is a ClassA type device based on the LoRaWAN open protocol. 

R72615A is connected to a variety of sensors. As detectors for CO2, temperature and humidity, the values collected by the sensor 

are reported to the corresponding gateway.   

 

LoRa Wireless Technology: 

LoRa is a wireless communication technology famous for its long-distance transmission and low power consumption. Compared 

with other communication methods, LoRa spread spectrum modulation technique greatly extend the communication distance. It 

can be widely used in any use case that requires long-distance and low-data wireless communications. For example, automatic 

meter reading, building automation equipment, wireless security systems, industrial monitoring. It has features like small size, 

low power consumption, long transmission distance, strong anti-interference ability and so on. 

 

LoRaWAN: 

LoRaWAN uses LoRa technology to define end-to-end standard specifications to ensure interoperability between devices and 

gateways from different manufacturers.   

 

 

 

 

 

 

 

 

 

 

 

 
 
 
 
 
 
 
 
 

 

 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for R72615A













Reviews: