background image

 

 

              811C000000000000000000 (configuration is successful) 

              811C010000000000000000 (configuration failed) 

 

Read device parameters 

       Downlink: 021C000000000000000000 

       Device returns: 

       821C003C003C0100010000 (current device parameters) 

 

 

 
Static, active 
threshold 

 

 

Active threshold 

The active threshold can be changed by the gateway issuing a command; 
Active activity threshold range is 0x0003-0x00FF (default is 0x0003); 
The scale factor of the threshold is 62.5 mg, and g is the gravitational acceleration at standard 
atmospheric pressure. 

 

Static threshold 

The Inactive static threshold can be changed by the gateway issuing command; 
Inactive static threshold range is 0x0002-0xFF (default is 0x0002) 
The scale factor of the threshold is 62.5 mg, and g is the gravitational acceleration at standard 
atmospheric pressure. 

 

Example

 

if you need to set the active threshold to 10m/s

²

, you need to set the value to 10/9.8/0.0625=16.32. 

The last value obtained is an integer and is configured as 16.

 

 

 
 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Example of threshold configuration: 

 

Assuming that the active threshold is set to 10m/s2, the value to be set is 10/9.8/0.0625=16.32. The last value obtained is an integer and is configured as 16. 

Assuming that the active threshold is set to 8m/s2, the value to be set is 8/9.8/0.0625=13.06, and the last value obtained is an integer and is configured as 13. 

 

Configure device parameters ActiveThreshold=16, InActiveThreshold=13 

       Downlink: 031C0010000D0000000000 Device returns: 

              831C000000000000000000 (configuration is successful) 

              831C010000000000000000 (configuration failed) 

 

Read device parameters 

       Downlink: 041C000000000000000000 

       Device returns: 

              841C0010000D0000000000 (device current parameter) 

 

 

 

Offset calibration

 

 

Description 

Device 

CmdI

DeviceType 

NetvoxPayLoadData 

SetActiveThres

holdReq 

 

R718E 

 

0x03 

0x1C 

ActiveThreshold(2Byt

es) 

InActiveThreshold(2Bytes) 

Reserved (5Bytes,Fixed 

0x00) 

SetActiveThres

holdRsp 

0x83 

Status(0x00_success) 

Reserved (8Bytes,Fixed 0x00) 

GetActiveThre

sholdReq 

0x04 

Reserved (9Bytes,Fixed 0x00) 

GetActiveThre

sholdRsp 

0x84 

Threshold(2Bytes) 

InActiveThreshold(2Bytes) 

Reserved (5Bytes,Fixed 

0x00) 

Summary of Contents for R718E









Reviews: