manualshive.com logo in svg

NetLink 700-883-PRO42, User Manual, Page: 33 / 68

Share
Download
NetLink 700-883-PRO42 User Manual Download Page 33

 

NETLink

®

 Switch 

 

33

7

 

Possibilities of the Web Interface 

If it has not been deactivated by the user, the web interface of the 
NETLink

®

 Switch can be opened with any standard browser (e.g. 

Internet Explorer, Firefox, Opera, etc.) 

The web interface is intended to support the user intuitively with 
information and configuration tasks. 

7.1

 

Home page 

The home page, which is located at ‘

http://<ip-address>,

’ is a basic 

address and navigation starting point for the user. 

 

From this page you can go to the status page, to the Basic Con-
figuration page, to the security page and, if the computer is con-
nected to the Internet, to the web site of Systeme Helmholz 
GmbH. 

The page also shows the contact data, such as postal address, 
phone and fax number, e-mail and web address. 

i

 

The NETLink

®

 PRO 

Compact has the IP ad-
dress 192.168.4.49 on 
delivery from the factory.

Summary of Contents for 700-883-PRO42





































































Reviews:

No comments