NETGEAR RT311 Reference Manual Download Page 93

Page: 93 / 125

Reference Guide for the Model RT311 and RT314 Internet Access Gateway Routers

System Maintenance

8-7

Figure 8-3.

Menu 24.4 - System Maintenance - Diagnostic

From the Main Menu, enter 24 to display Menu 24 - System Maintenance. Enter 4 to display Menu
24.4 - System Maintenance - Diagnostic. The available commands are listed in

Table 8-5

Table 8-5.

System Maintenance - Diagnostic Fields

Field

Command

Description

Ping host

[Enter 1]

This diagnostic test pings a local or remote host. You are prompted for
the IP address of the host.

WAN DHCP
Release

[Enter 2]

Release the DHCP-assigned parameters received from the ISP.

WAN DHCP
Renew

[Enter 3]

Issue a new DHCP request to the ISP for configuration parameters.

Intenet Setup Test

[Enter 4]

Attempt to login to the ISP, showing progress messages.

Reboot system

[Enter 11]

Your system is rebooted, implementing any changes that may have
been recently added to your system.

Menu 24.4 - System Maintenance- Diagnostic

TCP/IP

1. Ping Host

2. WAN DHCP Release

3. WAN DHCP Renewal

4. Internet Setup Test

System

11. Reboot System

Enter Menu Selection Number:

Summary of Contents for RT311






























































































































Search results

Summary of Contents for RT311

Reviews:

NETGEAR RT311, Reference Manual, Page: 93 / 125

Search results

Summary of Contents for RT311

Reviews: