NETGEAR RT311 Reference Manual Download Page 49

Reference Guide for the Model RT311 and RT314 Internet Access Gateway Routers

Using Your Browser for Configuring the Router

4-9

 

This screen shows the following statistics:.

Table 4-2.

Router Statistics Fields

Field

Description

Port

The statistics for the WAN (Internet) and LAN (local) ports. For each port, the screen 
displays:

Status

The link status of the port.

TxPkts

The number of packets transmitted on this port since reset or manual clear.

RxPkts

The number of packets received on this port since reset or manual clear.

Collisions

The number of collisions on this port since reset or manual clear.

Tx B/s

The current line utilization—percentage of current bandwidth used on this port.

Tx B/s

The average line utilization —average CLU for this port.

Up Time

The time elapsed since this port acquired link.

System up Time

The time elapsed since the last power cycle or reset.

Poll Interval

Specifies the intervals at which the statistics are updated in this window. Click on Stop 
to freeze the display.

Summary of Contents for RT311






























































































































Reviews: