background image

Note: The PS110/PS113 Print Server, by default, automatically obtains an IP
address from the network. However, NETGEAR recommends you use a fixed IP
address to be able to use a Web browser to print a test page or to make
configuration changes later. For a home or small office, use IP address information
compatible with your router setup. The IP address for the print server needs to be
unique in the network. If you don’t know what to use, you may click 

Suggest New

Values

to get a useable IP address. If you are using a NETGEAR router with default

settings, the following settings should work: IP address: 192.168.0.150 (The first
three numbers should match the numbers for the network device. Make sure the
last 3 digits are unique on your network.) 
Subnet mask: 255.255.255.0
Gateway IP address: 192.168.0.1 (the address of your router)

3.

When complete, click 

Finish

.

4.

When asked if you want to set up a printer right away, click 

Yes

and continue to

procedure 4: 

Configure a Computer To Access the Print Server

. You have already completed

the software installation and are running the 

NETGEAR Add Printer Wizard

.

Advanced Settings

Advanced users may want to change the default name of the Print Server or make other
changes in the settings. There are 2 ways to administer your NETGEAR Print Server. The

Reference Manual

on the 

Resource CD

has full instructions. 

a.  Open a Web browser and go to the IP address for the print server. (For example, type

http://192.168.0.150 and click 

Go

) or

b.  You can use the NETGEAR Print Server Administration program. Click

Start

. Point to

Programs

and click 

NETGEAR Print Server>NETGEAR Print Server Administration

6

Summary of Contents for PS110 - Print Server - Parallel




















Reviews: