NETGEAR Nighthawk RS400 User Manual Download Page 16

Page: 16 / 184

To cable your router:

1. Unplug your modem’s power, leaving the modem connected to the wall jack for

your Internet service.
If your modem uses a battery backup, remove the battery.

2. Plug in and turn on your modem.

If your modem uses a battery backup, put the battery back in.

3. Connect your modem to the Internet port of your router with the yellow Ethernet

cable that came with your router.

4. Connect the power adapter to your router and plug the power adapter into an outlet.

5. Press the Power On/Off button on the back panel of the router.

User Manual

Hardware Setup

Nighthawk AC2300 Cybersecurity WiFi Router Model RS400

Summary of Contents for Nighthawk RS400

























































































































































































Search results

Summary of Contents for Nighthawk RS400

Reviews:

Related manuals for Nighthawk RS400

Brands by name

Popular brands

NETGEAR Nighthawk RS400, User Manual

Search results

Summary of Contents for Nighthawk RS400

Reviews:

Related manuals for Nighthawk RS400

Brands by name

Popular brands