background image

YML739Rev1

V100LS User Guide

www.netcomm.com.au

11

Option A - Ethernet ADSL Internet Connection

Connect the V100LS ATA to your ADSL modem as illustrated in the following diagram:

Figure 1 - Connecting the V100LS ATA to an ADSL Modem

Note:

In the above configuration you must ensure your ADSL modem has DHCP

enabled. Should your modem not support DHCP, please refer to Appendix C of
this manual for instructions on how to configure the V100 ATA.

1. Connect the Phone socket on the rear of your V100LS ATA to an analogue telephone using

a RJ-11 cable.

2. Connect the WAN socket on the rear of your V100LS ATA  one of the LAN ports of your

router/switch using a Category 5 cable.

Note:

If you do not have any spare Ethernet ports on your ADSL modem / router and

you would like to connect to the Internet with your PC, you will need to add a
switch to the ADSL modem.

3. Connect the POWER socket on the rear of your V100LS ATA to the power adaptor

supplied and plug into a wall socket.

4. Everything required to connect to the VOIP network is preprogrammed into your V100LS

ATA.  To make a VoIP call, simply pick up the handset of your connected Analogue
Telephone and make the call.   Your new MyNetFone VOIP number can be located on the
base of the V100LS ATA unit.

Note:

If you have a Telstra telephone line you are still able to receive PSTN calls, but

you will need a microfilter and an additional analogue telephone. 

Do not under

any circumstanced connect the V100LS directly to a phone line.

Summary of Contents for V100









































Reviews: