NetApp AFF A200 Manual Download Page 61 | Manualshive

Page: 61 / 79

background image

Option 1: Replace SSD

1. If you want to manually assign drive ownership for the replacement drive, you need to disable

automatic drive assignment replacement drive, if it is enabled

You manually assign drive ownership and then reenable automatic drive assignment
later in this procedure.

a. Verify whether automatic drive assignment is enabled:

storage disk option show

You can enter the command on either controller module.

If automatic drive assignment is enabled, the output shows

on

in the “Auto Assign” column (for

each controller module).

b. If automatic drive assignment is enabled, disable it:

storage disk option modify -node

node_name -autoassign off

You must disable automatic drive assignment on both controller modules.

2. Properly ground yourself.

3. Physically identify the failed drive.

When a drive fails, the system logs a warning message to the system console indicating which drive
failed. Additionally, the attention (amber) LED on the drive shelf operator display panel and the failed
drive illuminate.

The activity (green) LED on a failed drive can be illuminated (solid), which indicates
that the drive has power, but should not be blinking, which indicates I/O activity. A failed
drive has no I/O activity.

4. Remove the failed drive:

a. Press the release button on the drive face to open the cam handle.

b. Slide the drive out of the shelf using the cam handle and supporting the drive with your other

hand.

5. Wait a minimum of 70 seconds before inserting the replacement drive.

This allows the system to recognize that a drive was removed.

6. Insert the replacement drive:

a. With the cam handle in the open position, use both hands to insert the replacement drive.

b. Push until the drive stops.

c. Close the cam handle so that the drive is fully seated into the mid plane and the handle clicks into

place.

Be sure to close the cam handle slowly so that it aligns correctly with the face of the drive.

7. Verify that the drive’s activity (green) LED is illuminated.

When the drive’s activity LED is solid, it means that the drive has power. When the drive’s activity LED

59

«
...
59
60
61
62
63
...
»

Summary of Contents for AFF A200
















































































Reviews:

No comments

Related manuals for AFF A200

ShareCenter DNS-343

Brand: D-Link Pages: 12

Z-DRIVE R2 E88 512GB PCI-EXPRESS X8 SSD

Brand: OCZ Pages: 2

Brand: LaCie Pages: 22

Brand: Quantum Pages: 345

Brand: Et Pages: 22

SkyHawk AI ST10000VE001

Brand: Seagate Pages: 32

Brand: Samsung Pages: 5

Brand: Samsung Pages: 10

Brand: Samsung Pages: 10

Brand: Samsung Pages: 15

Portable SSD X5

Brand: Samsung Pages: 22

Brand: Samsung Pages: 36

Brand: Samsung Pages: 27

Brand: Samsung Pages: 27

Brand: Samsung Pages: 36

Brand: Samsung Pages: 51

Brand: Samsung Pages: 54

Brand: Samsung Pages: 119

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands