NetApp AFF A200 Manual Download Page 3

Page: 3 / 79

AFF A200 System Documentation

Install and setup

Cluster configuration worksheet - AFF A200

You can use the

Cluster Configuration Worksheet

to gather and record your site-specific IP addresses and

other information required when configuring an ONTAP cluster.

Start here: Choose your installation and setup experience

You can choose from different content formats to guide you through installing and setting
up your new storage system.

•

Quick steps

A printable PDF of step-by-step instructions with live links to additional content.

•

Video steps

Video step-by-step instructions.

Installation and setup PDF poster - AFF A200

You can use the

AFF A200 Installation and Setup Instructions

poster to install and set up your new system.

The PDF poster provides step-by-step instructions with live links to additional content.

Installation and setup video - AFF A200

The

AFF A200 Setup Video

shows end-to-end software configuration for systems running ONTAP 9.2.

Maintain

Boot media

Overview of boot media replacement - AFF A200

The boot media stores a primary and secondary set of system (boot image) files that the
system uses when it boots. Depending on your network configuration, you can perform
either a nondisruptive or disruptive replacement.

What you’ll need

You must have a USB flash drive, formatted to FAT32, with the appropriate amount of storage to hold the

image_xxx.tgz

file.

Before you begin

• The nondisruptive and disruptive methods for replacing a boot media both require you to restore the var file

system:

Summary of Contents for AFF A200
















































































Search results

Summary of Contents for AFF A200

Reviews:

NetApp AFF A200, Manual, Page: 3 / 79

Search results

Summary of Contents for AFF A200

Reviews: