NetApp AFF A200 Manual Download

Page: 30 / 79

If your system is running
ONTAP…

Then…

Resulted in some test failures

Determine the cause of the problem.

a. Exit Maintenance mode:

halt

b. Perform a clean shutdown, and then disconnect the power

supplies.

c. Verify that you have observed all of the considerations identified

for running system-level diagnostics, that cables are securely
connected, and that hardware components are properly installed
in the storage system.

d. Reconnect the power supplies, and then power on the storage

system.

e. Rerun the system-level diagnostics test.

Step 3: Return the failed part to NetApp

Return the failed part to NetApp, as described in the RMA instructions shipped with the kit. See the

Part Return

& Replacements

page for further information.

Controller module

Overview of controller module replacement - AFF A200

You must review the prerequisites for the replacement procedure and select the correct
one for your version of the ONTAP operating system.

What you’ll need

• All drive shelves must be working properly.

• If your system is in an HA pair, the healthy controller must be able to take over the controller that is being

replaced (referred to in this procedure as the “impaired node”).

About this task

• You must replace the failed component with a replacement FRU component you received from your

provider.

• You must replace a controller module with a controller module of the same model type. You cannot

upgrade your system by just replacing the controller module.

• You cannot change any drives or drive shelves as part of this procedure.

• In this procedure, the boot device is moved from the impaired controller to the

replacement

node so that

the

replacement

node will boot up in the same version of ONTAP as the old controller module.

• It is important that you apply the commands in these steps on the correct systems:

◦

The

impaired

node is the controller that is being replaced.

◦

The

replacement

node is the new controller that is replacing the impaired controller.

◦

The

healthy

node is the surviving controller.

Summary of Contents for AFF A200
















































































Search results

Summary of Contents for AFF A200

Reviews:

Related manuals for AFF A200

Brands by name

Popular brands

NetApp AFF A200, Manual

Search results

Summary of Contents for AFF A200

Reviews:

Related manuals for AFF A200

Brands by name

Popular brands