manualshive.com logo in svg

Net2Edge LIB-306, Install Manual

Share
Download
Net2Edge LIB-306 Install Manual Download Page 24

Net2Edge 

 

LIB-306 Install Guide 

Install Guide Rev. D 

                              www.net2edge.com 

Page 24 of 25 

European Regulations 

WARNING: 

This is a Class A product. In a domestic environment, this product could cause radio 

interference in which case the user may be required to take adequate measures. 

Achtung !  

Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können bei Betrieb 

dieses Gerätes Rundfunkstörungen auftreten.  In diesem Fäll ist der Benutzer für Gegenmaßnahmen 

verantwortlich. 

Attention !  

Ceci est un produit de Classe A.  Dans un environment domestique, ce produit risque de créer 

des interférences radioélectriques, il appartiendra alors à l

’utilsateur de prende les measures spécifiques 

appropriées. 

In accordance with European Union Directive 2002/96/EC of the European Parliament and of the 

Council of 27 January 2003, Net2Edge will accept post usage returns of this product for proper 

disposal. The contact information for this activity can be found in the 

‘Contact Us’ portion of this 

document. 

CAUTION: RJ connectors are NOT INTENDED FOR CONNECTION TO THE PUBLIC 

TELEPHONE NETWORK. Failure to observe this caution could result in damage to the public 

telephone network. 

 
Der Anschluss dieses Gerätes an ein öffentlickes Telekommunikationsnetz in den EG-Mitgliedstaaten 
verstösst gegen die jeweligen einzelstaatlichen Gesetze zur Anwendung der Richtlinie 91/263/EWG zur 
Angleichung der Rechtsvorschriften der Mitgliedstaaten über Telekommunikationsendeinrichtungen 
einschliesslich der gegenseitigen Anerkennung ihrer Konformität. 

 

Summary of Contents for LIB-306


























Reviews:

No comments

Brands by name

Popular brands

Load more brands