background image

“Australia’s largest 

designer and 

manufacturer of 

high quality security 

products”

InstallatIon & ProgrammIng manual

For products: 
101-095 ness W1-B ultraprox reader/Controller

CoPyrIght notICe
all rights reserved. no part of this publication may be reproduced, transmitted or stored in a retrieval system in any form or by any 
means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of ness.  
ness reserves the right to make changes to features and specifications at any time without prior notification in the interest of 
ongoing product development and improvement.
© 2011 ness Corporation Pty ltd aBn 28 069 984 372   

www.ness.com.au

head oFFICe:
ness Corporation Pty ltd
aBn 28 069 984 372
Ph +61 2 8825 9222  Fax +61 2 9674 2520
ness@ness.com.au

sydney
Ph 02 8825 9222  Fax 02 9674 2520
sales@ness.com.au

melBourne
Ph 03 9875 6400  Fax 03 9875 6422
nessmelb@ness.com.au

BrIsBane
Ph 07 3399 4910  Fax 07 3217 9711
nessbris@ness.com.au

Perth
Ph 08 9328 2511  Fax 08 9227 7073
nessper@ness.com.au

adelaIde
Ph 08 8152 0000  Fax 08 8152 0100
adelaide@ness.com.au

n55

Summary of Contents for W1-B














Reviews: