Nera saturn bp, Technical Manual

Page: 36 / 44

34
Saturn Bp Portable – Technical Manual
configuration mistakes are made and the user
has difficulties in recovering the system. It
resets all configuration values to default.
Service printouts on PC
Information from the following functions can be
routed to a PC:
• Active alarms, function no. 30
• Info log, function no. 31
• Clear cause log, function no. 32
• Terminal Status, function no. 33 *
• Statistic info, function no. 34 *
Connection
A modem cable is connected between the DTE
port on the MCU and the Serial port of the PC.
A terminal emulator program, e.g. Procomm,
must be set up with the following port configura-
tion:
Default 19.2 Kbps, 8-bit, no parity, 1 stopbit,
or as set with function no.86, see Saturn B Data
Service Operator’s Manual.
General
The diagram provides an overview of all Saturn
Bp functions, including five special "Service
Level" functions:
• Terminal Status, function no. 33 *
• Statistic info, function no. 34 *
• Error, function no. 35
• Restart cause, function no. 36
• Erase all NV data, function no. 79
The "Service Level" is selected with the "SET
USER LEVEL" function no. 12.
(See "Setting User Level" in the Operator’s
Manual)
The service level is set by keying 5 when select-
ing level, and entering the password 753951
when prompted.
(1=user level, 2=operator level, 5=service level).
Terminal Status (3)3
*
The Terminal Status function shows the status
of several test points monitored in the MCU.
The signals are marked with an asterisk (*) on
the MCU and Antenna Unit block diagrams.
They are also listed in the Terminal Status
Table.
Statistic Info (3)4
*
The Statistic Info function has no relevance for
service. It should only be used on request from
NERA.
Error (3)5
The (SW) error function has no relevance for
service. It should only be used on request from
NERA.
Restart Cause (3)6
The Restart Cause function displays the reason
for the latest restart causes. It always contains
at least the Power up restart cause.
The function is a development tool, and has no
relevance for service. It should only be used on
request from NERA.
Erase all NV data (7)9
The Erase all NV data function can be used if
Number lists
and user lev.
1–
Region and
antenna ctrl
2–
Alarms and
messages
3–
System
information
4–
★
Terminal
config
5–
★
Bulletin
board data
6–
★
Installation
commands
7–
★
Enhanced
functions
8–
★
User level
Operator level
★
BB Status
(6)1
★★
Randomize
advice
(6)2
★★
Fwd channel
advice
(6)5
★★
Return chnl
advice
(6)6
★★
Sat.param.
advice
(6)7
★★
Registration
status
(6)8
★★
Active NCS
and spot id
(6)9
★★
MES Id
(4)0
★
MCU program
version
(4)1
★
ACU type
ACU/PCU ver
(4)2
★
DSP PROM
version
(4)3
★
Boot PROM /
handset ver.
(4)4
★
Enhanced
setup
(8)9
★
Active
alarms
(3)0
Info
log
(3)1
Clear
cause log
(3)2
★
Terminal
status
(3)3
★
Menus:
Explanation of keys:
Reverts to
previous
position
Deletes
entry
Scrolls
down/
up
through
choices
Displays
additional
information
Arrow in the display
indicates that more
information is available:
Moves to the next
choice, or enters
the selected one
Selects FUNCTIONs,
and displays HELP
page if any
Current
ocean region
(2)0
Geographic
position
(2)1
★
Nav area
(2)2
★
IMO SAR
area
(2)3
★
WMO area
(2)4
★
ICAO SAR
area
(2)5
★
Default LES
(5)0
★
Contrast
adjust
(5)1
★
Ring volume
adjust
(5)2
★
Date and
time
(5)3
★
Stand-alone
LES
(5)4
★
LES
capabilities
(6)0
★
Configure
ports
(7)0
★
Incoming
call route
(7)1
★
Commission
status
(7)2
★
Various
config
(7)7
★
Short number
list
(1)0
Last number
list
(1)1
Set user
level
(1)2
Set
password
(1)3
★
Group id
numbers
(1)4
★
☞
☞
ENTER
ENTER
☞
LIST
☞
☞
LIST
LIST
MORE/
HELP
☞
DEL
☞
☞
ESC
FUNC
☞
FUNC
☞
ESC
☞
Functions no.80 – 88 depend on Saturn Mp configuration
Erase all
NV data
(7)9
★★
SCAR
list
(1)9
★★
Statistic
info
(3)4
★★
Error
(3)5
★★
Restart
cause
(3)6
★★
Service level
★★
S e r v i c e
S e r v i c e S e r v i c e Service Level Functions