Neousys Technology Nuvo-2400 Series User Manual Download Page 28

Page: 28 / 81

Nuvo-2400

User’s Manual

Page 28 of 81

3.2.2 Parallel Port

Figure 13: Internal parallel port

Nuvo-2400 Series provides one parallel port for connecting a printing device. The parallel

port is implemented using industrial-grade ITE 8783 Super IO chip (-40 to 85°C) and has

pin-out via a 2x13, 2.0mm pitch box header. For users who need to connect a printing

device via a standard a 25-pin D-sub connector, Neousys Technology Inc. provides an

optional panel/cable kit to expose one a 25-pin D-sub (parallel) and one a 9-pin D-sub

(COM port). The following table describes the pin definition of the parallel port.

Table 12: Pin definition of parallel port

Pin No

Definition

Pin No Definition

Pin No

Definition

Pin No

Definition

Strobe

Data6

Linefeed

Ground

Data0

Data7

Error

Ground

Data1

Ack

Reset

Ground

Data2

Busy

Select-Print

Ground

Data3

Paper-Out

Ground

Data4

Select

Ground

Data5

The following figure shows the pin numbering of the optional panel/cable kit of the parallel

port.

Figure 14: Pin numbering of the panel/cable kit of parallel port

Summary of Contents for Nuvo-2400 Series


















































































Search results

Summary of Contents for Nuvo-2400 Series

Reviews:

Related manuals for Nuvo-2400 Series

Brands by name

Popular brands

Neousys Technology Nuvo-2400 Series, User Manual

Search results

Summary of Contents for Nuvo-2400 Series

Reviews:

Related manuals for Nuvo-2400 Series

Brands by name

Popular brands