Neousys Technology NRU Series Page 34 User Manual Download

Page: 34 / 73

NRU Series

2.4.6

10GbE Ethernet Port (NRU-110V Only)

Utilizing Intel’s X550-AT2 controller, the RJ45 10GBAST-T connector offers up

to 10Gb bandwidth throughput over a maximum distance of 100 meters using

Cat 6a or 55 meters using Cat 6 cables. It is ideal as a camera hub to deliver

real-time image or video to other computers.

Item

Description

10Gbit PoE+

Ethernet port

The two 10Gbit Ethernet ports are implemented via

Intel® X550-AT2 controller that supports 15.5K jumbo

frame, teaming and IEEE 1588

Active/Link LED (Right)

LED
Color

Status

Description

Green

Off

Ethernet port is disconnected

Ethernet port is connected and no data
transmission

Flashing

Ethernet port is connected and data is
transmitting/receiving

Speed LED (Left)

LED
Color

Status

Description

Green or
Orange

Off

100 Mbps

Orange

1000 Mbps

Green

10 Gbps

Summary of Contents for NRU Series










































































Search results

Summary of Contents for NRU Series

Reviews:

Related manuals for NRU Series

Brands by name

Popular brands

Neousys Technology NRU Series, User Manual

Search results

Summary of Contents for NRU Series

Reviews:

Related manuals for NRU Series

Brands by name

Popular brands