Neousys Technology NRU Series User Manual Download | Manualshive

Page: 35 / 73

background image

NRU Series

35

2.5

Internal I/O

The system’s internal I/O connectors consist of an M.2 slot for NVMe SSD, mini

PCIe slot and corresponding SIM slot.

2.5.1

M.2 2280 (M Key) Slot for NVMe SSD

The system has an M.2 2280 slot (M key PCIe Gen3 x2) to install an NVMe

SSD for the ultimate disk read/ write performance. An NVMe SSD offers

significantly more disk read/ write speed performances over 2.5” SSDs.

«
...
33
34
35
36
37
...
»

Summary of Contents for NRU Series










































































Reviews:

No comments

Related manuals for NRU Series

Brand: TechNexion Pages: 37

Brand: J.Burrows Pages: 24

Brand: BTOD Pages: 12

Brand: Ruijie Networks Pages: 30

Brand: Casio Pages: 133

ESPRIMO Q5 Series

Brand: Fujitsu Pages: 61

Toughbook CF-W8EWRZZAM

Brand: Panasonic Pages: 2

Toughbook CF-W8EWEZZAM

Brand: Panasonic Pages: 2

Toughbook CF-T8EWATZJM

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 36

Toughpad FZ-M1CCAAXBM

Brand: Panasonic Pages: 68

Brand: Panasonic Pages: 36

Brand: Panasonic Pages: 32

Brand: Panasonic Pages: 56

Brand: Panasonic Pages: 48

Brand: Panasonic Pages: 52

Brand: Panasonic Pages: 67

CF- - Toughbook 29 - Pentium M 1.6 GHz

Brand: Panasonic Pages: 80

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands