background image

 «Neomatica» Wireless sensor-immobilizer ADM33, edition 1.1 dd 11.11.2019        

 

2. 

Technical features 

 

 

Operation temperature range: from - 40°С up to + 85°С;  

 

Data transmission: Bluetooth Low Energy 4.1;  

 

Radio interface frequencies range: 2400...2483,5 MHz; 

 

Transmitter power: +4 dBm;  

 

Receiver sensitivity: -96 dBm;  

 

Coverage: up to 50 m at direct line of sight; 

 

Maximum supply voltage while using electromechanical relay: 15V; 

 

Rated current in contact elements of electromechanical relay: 9 A; 

 

Maximum voltage of the contact elements of electromechanical relay: 16 V; 

 

Maximum supply voltage when using semiconductor switches: 40 V; 

 

Maximum commuted current of semiconductor switches: 0.9 A; 

 

Maximum voltage between GND and NO outlets (Output 1): 40 V; 

 

Maximum voltage between GND and NС outlets (Output 2): 40 V; 

 

Maximum voltage between GND and COM outlets: 40 V; 

 

Current at which protection of semiconductor switches is activated, at t=25°С: 1.3 А; 

 

Consumption current (at supply voltage of 12 V): 2мА - 6мА when the semiconductor 

switches and electromechanical repay are switched off; 

 

Consumption  current  (at  supply  voltage  of  12  В):  8мА  when  the  semiconductor 

switches are switched on, without load; 

 

Consumption current (at supply voltage of 12 V): 55мА when electromechanical relay 

is switched on; 

 

IP class: IP65;  

 

Body material: polyolefin; 

 

Dimensions, mm: at most 17 x 21 x 80 (380 with cables);  

 

Weight: at most 34 g 

 

 

Summary of Contents for ADM33



















Reviews: