Nemalux XR8 Installation Manual Download Page 2

Ambient Temperature Range:

 

Connections:   

Standard 10ft 18/3 SOOW

 

 

 

Dimming 10ft 18/5 SOOW

 

 

 

Refer to wiring diagrams for connections. Class 1 Wiring only.

 

 

 

All supply field wiring must be rated 300V minimum for luminaires with suffix AC, 

 

 

 

600V minimum for luminaires with suffix HV.

Ingress Protection:  IP68 Continuous Submersion 25ft | Suitable for Wet Locations. | Marine Outside Type 

 

 

 

(Salt Water)                                                                  

XR-EN

rev. B-02

2-7

www.nemalux.com  |   [email protected]  |   Tel 403•242•7475  |   Fax 403•243•6190 

MADE IN CANADA

APPLICATION Cont.

LUMINANCE

XR8 

XR10 

XR15 

XR20 

Temp Range General Location

(Deg C)

-50 to 75

-50 to 74

-50 to 74

-50 to 67

WARNING

ATTENTION

Potential Electrostatic Charging Hazard
Risque potentiel de charge électrostatique 

Avoid electrostatic discharge :

• Clean exterior lens surface with damp cloth only

• Éviter les décharges électrostatiques: nettoyer la surface extérieure de la lentille uniquement 

   avec un chiffon humide

To reduce the risk of electric shock, 

disconnect the luminaire from the 

supply circuit before opening for 

installation and servicing.  Keep 

tightly closed when in operation.

WARNING / ATTENTION

  

To avoid the risk of fire, explosion, 

or electric shock, this product 

should be installed, inspected, and 

maintained by a qualified 

electrician only, in accordance with 

all applicable electrical codes.

Éviter tout risque d'incendie, 

d'explosion ou d'électrocution, ce

produit doit être installé, inspecté 

et entretenu par un électricien 

qualifié uniquement, 

conformément à tous

codes électriques applicables.

WARNING / ATTENTION

Pour réduire le risque de choc électrique, 

débranchez le luminaire du circuit 

d'alimentation avant l'ouverture pour 

l'installation et entretien. Gardez 

hermétiquement fermé pendant le 

fonctionnement.

Summary of Contents for XR8








Reviews: