GENERAL INFORMATION
Carefully read this instruction manual for installation and use before putting the FLIK
sliding system into operation; this will help to prevent errors and time
in maximum safety.
This documentation is intended for specialised companies and end users. All installation,
maintenance and repair work should be carried out by suitably trained technical personnel.
After installation and testing, the technician must provide
a short demonstration of the use of the FLIK automated sliding door device.
USER INSTRUCTIONS
CAUTION: Carefully observe all the following installation instructions to
ensure personal safety.
The device is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lacking experience and knowledge.
Do not allow children to play with the fixed controls and keep any remote
units out of their reach.
Have installation checks performed periodically by qualified personnel from a
service centre authorised by the manufacturer. Do not use if repair or adjustment is
required.
CAUTION: if the power cable is damaged, it must be replaced by quali
personnel from a service centre authorised by the manufacturer.
CAUTION. Disconnect the power supply during cleaning or maintenance
operations. Do not use solvents or jets of water to wash the appliance; the
appliance should not be submerged in
In the event of fault or malfunction, switch off the device at the main switch. All
repairs and adjustments (e.g. setting the stroke) must only be performed by
qualified personnel from a service centre authorised by the manufacturer.
Always request exclusive use of original spare parts. Failure to respect this
condition could compromise safety and invalidate the benefits contained in the
warranty for the appliance. In the event of any problems or queries, consult your
agent or contact the manufactu
The A-weighted sound pressure level is less than 70dB(A).
Carefully preserve these instructions after installation.
3
GENERAL INFORMATION
Carefully read this instruction manual for installation and use before putting the FLIK
sliding system into operation; this will help to prevent errors and time
This documentation is intended for specialised companies and end users. All installation,
maintenance and repair work should be carried out by suitably trained technical personnel.
After installation and testing, the technician must provide the user with these instructions and give
a short demonstration of the use of the FLIK automated sliding door device.
USER INSTRUCTIONS
CAUTION: Carefully observe all the following installation instructions to
ensure personal safety.
The device is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lacking experience and knowledge.
Do not allow children to play with the fixed controls and keep any remote
Have installation checks performed periodically by qualified personnel from a
service centre authorised by the manufacturer. Do not use if repair or adjustment is
CAUTION: if the power cable is damaged, it must be replaced by quali
personnel from a service centre authorised by the manufacturer.
CAUTION. Disconnect the power supply during cleaning or maintenance
operations. Do not use solvents or jets of water to wash the appliance; the
appliance should not be submerged in water.
In the event of fault or malfunction, switch off the device at the main switch. All
repairs and adjustments (e.g. setting the stroke) must only be performed by
qualified personnel from a service centre authorised by the manufacturer.
t exclusive use of original spare parts. Failure to respect this
condition could compromise safety and invalidate the benefits contained in the
warranty for the appliance. In the event of any problems or queries, consult your
agent or contact the manufacturer directly.
weighted sound pressure level is less than 70dB(A).
Carefully preserve these instructions after installation.
Carefully read this instruction manual for installation and use before putting the FLIK
sliding system into operation; this will help to prevent errors and time-wasting and to work
This documentation is intended for specialised companies and end users. All installation,
maintenance and repair work should be carried out by suitably trained technical personnel.
the user with these instructions and give
a short demonstration of the use of the FLIK automated sliding door device.
CAUTION: Carefully observe all the following installation instructions to
The device is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lacking experience and knowledge.
Do not allow children to play with the fixed controls and keep any remote-control
Have installation checks performed periodically by qualified personnel from a
service centre authorised by the manufacturer. Do not use if repair or adjustment is
CAUTION: if the power cable is damaged, it must be replaced by qualified
personnel from a service centre authorised by the manufacturer.
CAUTION. Disconnect the power supply during cleaning or maintenance
operations. Do not use solvents or jets of water to wash the appliance; the
In the event of fault or malfunction, switch off the device at the main switch. All
repairs and adjustments (e.g. setting the stroke) must only be performed by
qualified personnel from a service centre authorised by the manufacturer.
t exclusive use of original spare parts. Failure to respect this
condition could compromise safety and invalidate the benefits contained in the
warranty for the appliance. In the event of any problems or queries, consult your
INSTALLER INSTRUCTIONS
1. SECURITY RULES
CAREFULLY
OBSERVE
INSTRUCTIONS
TO
INSTALLATION
CAN
The Nekos electrical actuators comply with the Machinery Directive (2006/42/EC), Standard IEC
60335-2-103 (Particular requirements for drives for gates, doors and windows) and other directives
and regulations indicated in the attached Declarations of Incor
end of the manual). According to the Machinery Directive, actuators are “partly completed
machinery” intended for incorporation into doors and windows.
The manufacturer/supplier of the window is
compliance of the entire system with the applicable standards and to issue
strongly discourage any use of the actuators other than that specified and ther
the supplier of the complete system retains full liability.
MANDATORY
RISK
ANALYSIS
For systems installed at a height of less than 2.5 m above floor level or other levels accessible to
users, the manufacturer/supplier of the window must conduct
harm (violent blows, crushing, wounds) caused to people by no
accidental breakage of the automated windows, and to implement suitable
view of these. Such measures include those recommended by the specified standard:
-
controlling the actuators via a “deadman’s
operator’s field of view, to ensure that people are out of the way during operation. The button
must be placed at a height of 1.5 m and operated by key if accessible to the public; or:
use contact safety systems (also included in the devices) that ensure a maximum closing force
of 400/150/25 N, measured in accordance with paragraph BB.20.107.2 of IEC 60335
or:
- use of non-contact safety systems (lasers, light grids); or:
- use of fixed safety barriers that
Automated windows are deemed adequately protected if they:
are installed at a height of >2.5 m; or:
have a leading-edge opening of <200 mm and a closing speed of <15 mm/s; or:
are part of a smoke and heat evacuation system
The device is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lacking experience and knowledge. Do not allow
children to play with the fixed controls and keep any remo
reach.
The actuator is destined exclusively for installation indoors. For any special application we
recommend you consult the manufacturer beforehand.
After removing packaging, check for any damage on the appliance.
Always request exclusive use of original spare parts. Failure to respect this condition
could compromise safety and invalidate the benefits contained in the warranty for the
appliance.
In the event of any problems or queries, consult your agent or contact
directly.
4
INSTALLER INSTRUCTIONS
OBSERVE
ALL
THE
FOLLOWING
TO
ENSURE
PERSONAL
SAFETY.
CAN
SERIOUSLY
ENDANGER
SAFETY.
The Nekos electrical actuators comply with the Machinery Directive (2006/42/EC), Standard IEC
103 (Particular requirements for drives for gates, doors and windows) and other directives
and regulations indicated in the attached Declarations of Incorporation and
end of the manual). According to the Machinery Directive, actuators are “partly completed
machinery” intended for incorporation into doors and windows.
The manufacturer/supplier of the window is required, with exclusive responsibility, to ensure the
compliance of the entire system with the applicable standards and to issue
strongly discourage any use of the actuators other than that specified and ther
the supplier of the complete system retains full liability.
ANALYSIS
AND
PROTECTION
MEASURES.
For systems installed at a height of less than 2.5 m above floor level or other levels accessible to
users, the manufacturer/supplier of the window must conduct
risk analysis
harm (violent blows, crushing, wounds) caused to people by normal use or possible malfunction or
accidental breakage of the automated windows, and to implement suitable
view of these. Such measures include those recommended by the specified standard:
controlling the actuators via a “deadman’s button” placed near the system and within the
operator’s field of view, to ensure that people are out of the way during operation. The button
must be placed at a height of 1.5 m and operated by key if accessible to the public; or:
ms (also included in the devices) that ensure a maximum closing force
of 400/150/25 N, measured in accordance with paragraph BB.20.107.2 of IEC 60335
contact safety systems (lasers, light grids); or:
use of fixed safety barriers that prevent access to moving parts.
Automated windows are deemed adequately protected if they:
are installed at a height of >2.5 m; or:
edge opening of <200 mm and a closing speed of <15 mm/s; or:
are part of a smoke and heat evacuation system for emergency use only
The device is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lacking experience and knowledge. Do not allow
children to play with the fixed controls and keep any remote-control units out of their
The actuator is destined exclusively for installation indoors. For any special application we
recommend you consult the manufacturer beforehand.
After removing packaging, check for any damage on the appliance.
request exclusive use of original spare parts. Failure to respect this condition
could compromise safety and invalidate the benefits contained in the warranty for the
In the event of any problems or queries, consult your agent or contact
INSTALLER INSTRUCTIONS
FOLLOWING
INSTALLATION
SAFETY.
IMPROPER
The Nekos electrical actuators comply with the Machinery Directive (2006/42/EC), Standard IEC
103 (Particular requirements for drives for gates, doors and windows) and other directives
poration and
Conformity (at the
end of the manual). According to the Machinery Directive, actuators are “partly completed
required, with exclusive responsibility, to ensure the
compliance of the entire system with the applicable standards and to issue
certification. We
strongly discourage any use of the actuators other than that specified and therefore, in any case,
MEASURES.
For systems installed at a height of less than 2.5 m above floor level or other levels accessible to
risk analysis
regarding potential
rmal use or possible malfunction or
accidental breakage of the automated windows, and to implement suitable protective measures in
view of these. Such measures include those recommended by the specified standard:
button” placed near the system and within the
operator’s field of view, to ensure that people are out of the way during operation. The button
must be placed at a height of 1.5 m and operated by key if accessible to the public; or:
ms (also included in the devices) that ensure a maximum closing force
of 400/150/25 N, measured in accordance with paragraph BB.20.107.2 of IEC 60335-2-103;
edge opening of <200 mm and a closing speed of <15 mm/s; or:
for emergency use only
.
The device is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lacking experience and knowledge. Do not allow
control units out of their
The actuator is destined exclusively for installation indoors. For any special application we
After removing packaging, check for any damage on the appliance.
request exclusive use of original spare parts. Failure to respect this condition
could compromise safety and invalidate the benefits contained in the warranty for the
In the event of any problems or queries, consult your agent or contact the manufacturer