Neilsen CT2214 Instruction Manual Download Page 6

4

Only tow with recommended vehicles (Lawn/Garden Tractors and ATVs). Always
secure and lock dump cart to the vehicle hitch before operating.
This equipment is not designed to be used with zero-turn mowers.

NEVER LEAVE MACHINE RUNNING UNATTENDED.

Do not leave the

machine unattended until it has come to a complete stop.

TYRE INFLATION.

WARNING! Over-inflated tyres can explode and cause

serious injury. Avoid injury by NEVER over inflating tyres beyond the maximum
pressure printed on the side of the tyre wall. ALWAYS use FOOT or HAND pump
inflation devices.

INSPECT.

Before using, always visually inspect to see that the tools are not worn

or damaged. Replace worn or damaged elements and bolts in sets, to preserve
balance. Always secure and lock aerator spreader to the vehicle hitch before
operating.

CRUSH AND CUT HAZARDS.

Always keep hands and feet clear from moving

parts while operating the equipment. Always clear and keep work area clean
when operating. Always wear safety gear, eye protection, gloves and work
boots when operating the aerator spreader.

MAINTAIN YOUR MACHINE WITH CARE.

Clean the machine immediately after

use. Keep the machine clean to ensure it operates to its full & safest
performance. When maintaining this machine, only the manufacturer’s original
replacement parts should be used.

PROTECT THE ENVIRONMENT.

Take left over materials to an authorised

collection point or follow the stipulations in the country where the machine is
used. Do not discharge into drains, soil or water.

STORE IDLE EQUIPMENT.

When not in use, the machine should be stored in a

dry location. Keep the machine away from children and others not qualified to
use it.

Summary of Contents for CT2214





















Reviews: