background image

P2125EN00

01 - 2008

FILLER MEnu

2

1.2 - PRiNT REL.STATS.

1.2.1 - PARTiAL PRiNTiNG

1.2.1.1 - SELECT. COUNT.

1.2.1.2 - bAND COUNTER

1.2.1.3 - fAiLURE COUNT.

1.2.1.4 - COiN MECH.DATA

1.2.1.5 - PRiNT PHOT. ERR.

1.2  

P

rIntIng

 

the

 

relatIve

 

statIstIcs

1.2.1  

P

artIal

 

PrIntout

1.2.1.1  

P

rIntIng

 

the

 

selectIon

 

counters

When confirming this function, the relative counters regarding the 

different selections are printed.

1.2.1.2  

P

rIntIng

 

the

 

tIme

 

band

 

counters

When confirming this function, the relative counters regarding the 

different time bands are printed.

1.2.1.3  

P

rIntIng

 

the

 

faIlure

 

counters

When confirming this function, the relative counters regarding fail

-

ures are printed.

1.2.1.4  

P

rIntIng

 

the

 

coIn

 

mechanIsm

 

data

When confirming this function, the relative counters regarding the 

coin mechanism data are printed.

1.2.1.5 

P

rIntIng

 

the

 

Photocell

 

errors

When confirming this function, the relative counters regarding the 

photocell errors are printed.

1.2.1.6 - PRiNT MOTOR ERR.

1.2.1.6 

P

rIntIng

 

the

 

motor

 

errors

When confirming this function, the counters regarding the motor 

errors are printed.

1.2.2  

t

otal

 

PrIntout

When confirming this function, all relative statistics are printed.

1.2.2 - TOTAL PRiNTiNG

Summary of Contents for Rondo














































Reviews: