NEC WMK-3257, Installation And Assembly Manual

Page: 6 / 7

6 of 7
ISSUED: 03-26-10 SHEET #: 125-9106-6 12-11-14
To prevent scratching the screen, set a cloth on a fl at, level surface that will support the weight of the screen. Place
screen face side down. If screen has knobs on the back, remove them to allow the tilt brackets to be attached. Place
tilt brackets (
B and C ) on back of screen as shown in fi g. 2.2. Note: Be sure to attach tilt brackets with handles fac-
ing outward as in fi gure 2.2. Align tilt brackets to screen mounting holes as recommended by chart below. Attach the
tilt brackets to the back of the screen using the appropriate combination of screws, either M4 x 16 socket pin screws
(
N ), M6 x 12 mm socket pin screw ( G ), M6 x 20 socket pin screw ( H ), or M8 x 15 mm socket pin screw ( J ) with multi-
washers ( I ) as shown in fi gures 2.3 and 2.4. Verify that all holes are properly aligned, and then tighten screws using
security allen wrench ( F ).
2
Installing Tilt Brackets
Use Chart to Determine
Orientation
and Screws
Portrait
Landscape
USING
EXTENSION
BRACKETS
USING TILT
BRACKETS
ONLY
HANDLES
FACE OUT
Secure extension brackets ( L ) to left
tilt bracket ( B ) with four M5 x 6 mm
socket pin serrated washer head
screws (
K ).
Height of tilt brackets may be ad-
justed using holes above and below
center mounting location holes.
NOTE: Repeat using right tilt
bracket ( C ).
• Tighten screws so adapter brackets are fi rmly
attached. Do not tighten with excessive force.
Overtightening can cause stress damage to screws,
greatly reducing their holding power and possibly
causing screw heads to become detached.
Tighten to
40 in. • lb (4.5 N.M.) maximum torque.
• If screws don't get three complete turns in the screen
inserts or if screws bottom out and bracket is still
not tightly secured, damage may occur to screen or
product may fail.
WARNING
MAX Distance 400 mm
USE TILT BRACKET ONLY
WHEN MOUNTING TO
SCREEN USING 200 X 200
fi g 2.4 fi g 2.3
fi g 2.2
fi g 2.1
*
Use multi-washers ( I ) to attach tilt
brackets ( B and C ) to your screen
when using M4 x 16 socket pin
screws (
N ), M6 x 12 mm socket
pin screw ( G ), or M6 x 20 mm
socket pin
screws (
H )
M8 screws do not require
multi-washers (
I )
G, H, J, or N
B
C
I*
G, H,J,
or N
I*
B
C
L
K
B
400 mm
200 mm
300 mm
CENTER
MOUNTING
LOCATIONS
LANDSCAPE PORTRAIT
Recommended Hole Pattern Recommended Hole Pattern
A 100 mm x 100 mm D 400 mm X 400 mm A 100 mm x 100 mm D 400 mm X 400 mm
B 200 mm X 200 mm E 400 mm x 200 mm B 200 mm X 200 mm E 200 mm x 400 mm
C 300 mm X 300 mm C 300 mm X 300 mm
Screen Screw Size Screen Screw Size Screen Screw Size Screen Screw Size
B ASPV32 M6 x 12 C P401 M6 x 12 B ASPV32 M6 x 12 C P401 M6 x 12
B ASPV40 M6 x 12 C P461 M6 x 12 B ASPV40 M6 x 12 C P461 M6 x 12
B E321 M6 x 12 D P521 M6 x 12 B E321 M6 x 12 D P521 M6 x 12
A E324 M4 x 16 D P551 M6 x 12 A E324 M4 x 16 D P551 M6 x 12
E E421 M6 x 12 C S401 M6 x 12 E E421 M6 x 12 C S401 M6 x 12
E E461 M6 x 20 C S461 M6 x 12 E E461 M6 x 12 C S461 M6 x 12
B LCD3210 M6 x 12 D S521 M6 x 12 B LCD3210 M6 x 12 D S521 M6 x 12
B LCD3215 M6 x 12 B SC40 M6 x 12 B LCD3215 M6 x 12 B SC40 M6 x 12
E LCD4020 M6 x 12 B SC46 M6 x 12 E LCD4020 M6 x 12 B SC46 M6 x 12
E LCD4215 M6 x 12 E V321 M6 x 12 E LCD4215 M6 x 12 E V321 M6 x 12
E LCD4615 M6 x 12 E V421 M6 x 12 E LCD4615 M6 x 12 E V421 M6 x 12
E LCD4620 M6 x 12 E V461 M6 x 12 E LCD4620 M6 x 12 E V461 M6 x 12
D LCD5220 M6 x 12 C X431BT M6 x 12 D LCD5220 M6 x 12 C X431BT M6 x 12
E LCD5710 M8 x 15 C X461HB M6 x 12 E LCD5710 M8 x 15 C X461HB M6 x 12
E M40 M6 x 12 C X461UN M6 x 12 E M40 M6 x 12 C X461UN M6 x 12
E M46 M6 x 12 E M46 M6 x 12