background image

1

Wall Mount Unit

 Installation and Adjustment Manual

Thank you for your purchase of this NEC wall mount unit.
Please read this installation and adjustment manual carefully to ensure proper use.
The Wall Mount Unit NP02WK/NP03WK is exclusivelyfor Projector NP-M260XS/M300XS/
M350XS/M260WS/M300W  and cannot be used for other projectors.

Special skills are required to install the pojector. This work

should never be performed by the customer.

To the Dealer and Installer

be started after careful attention is paid to the strength of the

mounting location to ensure it will withstand the weight of the

projector and mounting hardware.

Please heed the following

CONTENTS

..................................................... 1

Preparation ........................................................................... 4

4

..

..

..

..

..

..

..

..

..

..

..

..

..

..

..

..

..

..

..

..

..

..

..

..

..

..

..

..

..

..

.s

tr

a

P

 

d

e

g

a

k

c

a

P

..

..

..

..

..

..

..

..

..

..

..

..

..

..

..

..

..

..

..

..

..

..

..

..

..

..

..

..

..

..

..s

tr

a

P

 f

o

 

s

e

m

a

N

5

Dimensions of Parts ................................................... 6

Mounting the Projector ........................................................ 7
Adjusting the Projection Position ......................................... 10
Specifications ...................................................................... 13

To ensure customer safety, we ask that the installation work

Summary of Contents for NP03WK















Reviews: