855-901060-001- A
NE3304-151
NE3304-152
Dual Port 1000BASE-T Adapter (EXP181A)
Quad Port 1000BASE-T Adapter (EXP182A)
1st. Edition
Contents
Item
Qty. Notes
Network Interface Card
1
By default, Low-profile bracket is attached.
Bracket
1
Either Standard type or Low-profile type.
By default, Standard type is packaged.
Warranty
1
This is not included if selected BTO. Instead,
the warranty of the server contains a warranty
of this product.
Startup Guide
1
This guide.
Startup Guide
Warranty
Network interface card
Bracket
NE3304-152M
(EXP182A)
NE3304-151M
(EXP181A)
For NE3304-152M
For NE3304-151M
Dual Port
1000BASE-T Adapter
Quad Port
1000BASE-T Adapter
Important :
This product does not contain a “Driver Software” disk.
Driver Software is published on NEC support site.
See the section
“Driver Installation / Uninstallation”
Note :
This warranty is available only for using in Japan. Do not
use it in any other than Japan.
Note
1.
No part of this guide may be reproduced, transmitted, translated in any form, or converted to
medias without prior written permission
2.
The contents of this guide are subject to change without prior notice.
3.
All efforts have been made to ensure the accuracy of all information in this guide. If you find
any part unclear, incorrect, or omitted in this guide, contact your service representative.
4.
The company assumes no liability arising from the use of this product, nor any liability for
incidental or consequential damage arising from the use of this guide regardless of 3 above.
5.
This guide is created for the manager or the maintenance person who is well informed
about the operation of this device. Note that the basic information, such as the operation
procedures of the device and OS, is omitted.
© NEC Corporation 2015
No part of this guide may be reproduced or changed in any form without prior written
permission of NEC Corporation.
FCC Compliance Information Statement, Class A
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to correct the interference
at his own expense.
Industry Canada Class A Emission Compliance Statement
This Class A digital apparatus complies with Canadian ICES-003.
Avis de conformité à la réglementation d'Industrie Canada
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
BSMI Statement
CE / Australia and New Zealand Statement
This is a Class A product. In domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures (EN55022).
KCC Notice Class A (Republic of Korea Only)
A
급
기기
(
업무용
방송통신기기
)
이
기기는
업무용
(A
급
)
으로
전자파적합등록을
한
기기이오니
판매자
또는
사용자는
이
점을
주의하시기
바라며
,
가정외의
지역에서
사용하는
것을
목적으로
합니다
.
Disposing of your used product
In the European Union
EU-wide legislation as implemented in each Member State requires that used
electrical and electronic products carrying the mark (left) must be disposed of
separately from normal household waste. This includes workstation or electrical
accessories. When you dispose of such products, please follow the guidance of
your local authority or ask the shop where you purchased the product, or if
applicable, follow applicable legislation or agreement you may have. The mark
on electrical and electronic products only applies to the current European Union
Member States.
Outside the European Union
If you wish to dispose of used electrical and electronic products outside the European Union,
please contact your local authority and ask for the correct method of disposal.
China RoHS
x:
表示
该
有毒有害物
质
至少在
该
部件的某一均
质
材料中的含量超出
SJ/T11363-
2006
标
准
规
定的限量要求
o
多溴二苯
醚
(PBDE)
o
六价
铬
(Cr6+)
o
汞
(Hg)
o:
表示
该
有毒有害物
质
在
该
部件所有均
质
材料中的含量均在
SJ/T11363-2006
标
准
规
定的限量要求以下
o
o
x
印刷
电
路
板
组
件
多溴
联
苯
(PBB)
镉
(Cd)
铅
(Pb)
有毒有害物
质
或元素
部件
名称
RoHS Compliant
Trademarks
Broadcom is among the trademarks of Broadcom Corporation and/or its affiliates in the United
States, certain other countries, and/or the EU.
PCI-EXPRESS
is a trademark of PCI-SIG. Any other trademarks or trade names mentioned
are the property of their respective owners.
Windows is a registered trademark of Microsoft Corporation in the United States
and other countries.
Linux is a registered trademark of Linus Torvalds.
Keep this Startup Guide at hand for quick reference at any
time necessary.
Be sure to read this section carefully.
Precautions for Use
-Be sure to read this section -
The following includes information necessary for proper and safe operation of the
product.
Safety Indication
Follow the instructions in this Startup Guide for your safety to use this product.
The server contains components with possible danger, hazards that may cause by ignoring
warnings, and preventive actions against such hazards. The words “WARNING” and “CAUTION”
are used to indicate the degrees of danger. These terms are defined as follows:
Indicates the presence of a hazard that may result in death
or serious personal injury if the instruction is ignored.
Indicates the presence of a hazard that may cause minor
personal injury, including burns, or property damage if the
instruction is ignored.
This guide uses the following three types of symbols to give indications and
precautions against a danger. They are defined as follows:
Attention
This symbol indicates the
presence of a hazard if the
instruction is ignored. An image in
the symbol illustrates the hazard
type.
Example
(Electric hazard)
Prohibited
action
This symbol indicates prohibited
actions. An image in the symbol
illustrates a particular prohibited
action.
Example
(Do not disassemble)
Mandatory
action
This symbol indicates mandatory
actions. An image in the symbol
illustrates a mandatory action to
avoid a particular hazard.
Example
(Unplug)
Do not plug the power cord in a
nonconforming outlet
Use a wall outlet with specified voltage and power type.
Otherwise, ther is a risk of a fire or current leakage.
Symbol to draw attention
Description of a danger
Term indication a degree of danger
Symbols Used in This Startup Guide
Attentions
Indicates a risk of an electric
shock.
Indicates a risk of a fire or
fumes.
Indicates a general precaution
or warning that cannot be
specifically identified.
Prohibited actions
Do not disassemble, repair, or
modify this product.
Otherwise, there is a risk of an
electric shock or fire.
Keep the product away from
water. Otherwise, there is a risk
of an electric shock or ignition.
Indicates a general prohibited
action.
Mandatory actions
Unplug the power cord of the
server. Otherwise, there is a
risk of an electric shock or fire.
Precautions for Safety
General Precautions
Do not use the product for services where critical
high availability may directly affect human lives.
The product is not intended to be used with or control facilities or
devices concerning human lives, including medical devices, nuclear
facilities and devices, aeronautics and space devices, transportation
facilities and devices; and facilities and devices requiring high
reliability. NEC assumes no liability for any accident resulting in
personal injury, death, or property damage if the product has been
used in the above conditions.
Do not continue to use the equipment if you detect
smoke, odor, or noise
If the equipment emits smoke, odor, or noise, immediately unplug the
power cord of the server. Then, contact your service representative.
Continuing to use the product in such condition may cause a fire.
Do not insert a wire or metal object
Do not insert a wire or metal object into this product.
There is a risk of an electric shock.
Keep water or foreign matter away from the
equipment.
Do not let any form of liquid (water etc.) or foreign matter (e.g., pins
or paper clips) enter the equipment. Failure to follow this warning
may cause an electric shock, a fire, or a failure of the equipment.
When such things accidentally enter the equipment, immediately
turn the power off and unplug the power cord. Then, contact your
service representative.
Precautions for Installation, Relocation, Storage and
Connection
Do not use any unauthorized interface cable.
Use only interface cables authorized by NEC and locate a proper
device and connector before connecting a cable. Using an
authorized cable or connecting a cable to an improper destination
may cause a short circuit, resulting in a fire.
Also, observe the following notes on using and connecting an
interface cable.
-
Do not use any damaged cable connector.
-
Do not step on the cable.
-
Do not put any object on the cable.
-
Do not use the card with the loose interface cable connection.
-
Do not use any damaged cable.
See also “
Network Cables
”
Do not use the equipment in the place where
corrosive gases exist.
Make sure not to locate or use the equipment in the place where
corrosive gases (sulfur dioxide, hydrogen sulfide, nitrogen dioxide,
chlorine, ammonia, ozone, etc) exist.
Also, do not set it in the environment where the air (or dust) includes
components accelerating corrosion (ex. sulfur, sodium chloride) or
conductive metals. There is a risk of a fire due to corrosion and
shorts of an internal printed board.
Contact your service representative for the place appropriate to the
equipment.
5
