NEC NC1500C User Manual Download Page 44

Page: 44 / 62

6. Appendix

6-2. Indicator display list

See the descriptions below when the blinking or lighting of the two indicators on the projector’s control panel and the rear

STATUS indicator on the backside of the projector is observed. The projector also has a warning function that uses a buzzer.

MMS

STATUS

MMS STATUS indicator

POWER indicator

STATUS indicator

6-2-1. POWER indicator

Indicator condition

Off

Blinking light

Steady light

Projector condition

The main power is off.

The projector is getting ready to turn on.

The douser is closed.

The projector is cooling down.

The projector is turned on.

The projector is in standby.

Note

Wait for a moment.

Green

Orange

Green

Orange

6-2-2. STATUS indicator

Indicator condition

Off

Blinking light (Red)

Projector condition

Normal

Error

Note

An error message is displayed in

the LCD screen. Check the content

of the error.

6-2-3. MMS STATUS indicator

Indicator condition

Off

Blinking light

Steady light

Projector condition

Multi-media switcher (MMS) not in use.

Link error

Preparing link with Built-in multi-media

switcher (MMS).

Preparing link with External multi-media

switcher (MMS).

Built-in multi-media switcher (MMS) is linked.

External multi-media switcher (MMS) is linked.

Note

Link error. An error message is

displayed in the LCD screen.

Check the content of the error.

Wait for a moment.

Red

Green

Orange

Green

Orange

Summary of Contents for NC1500C































































Search results

Summary of Contents for NC1500C

Reviews:

Related manuals for NC1500C

Brands by name

Popular brands

NEC NC1500C, User Manual

Search results

Summary of Contents for NC1500C

Reviews:

Related manuals for NC1500C

Brands by name

Popular brands