CBZ-033043-061-00
6
Precautions for Safety
General Precautions
Do not use the product for services where critical high availability may directly affect human
lives.
The product is not intended to be used with or control facilities or devices concerning human lives, including medical devices,
nuclear facilities and devices, aeronautics and space devices, transportation facilities and devices; and facilities and devices
requiring high reliability. NEC assumes no liability for any accident resulting in personal injury, death, or property damage if
the product has been used in the above conditions.
Observe warnings and cautions for server.
Be sure to observe warnings and cautions for server when using this product.
Do not continue to use the equipment if you detect smoke, odor, or noise
If the equipment emits smoke, odor, or noise, immediately unplug the power cord of the server. Then, contact your service
representative. Continuing to use the product in such condition may cause a fire.
Keep water or foreign matter away from the equipment.
Do not let any form of liquid (water etc.) or foreign matter (e.g., pins or paper clips) enter the equipment. Failure to follow this
warning may cause an electric shock, a fire, or a failure of the equipment. When such things accidentally enter the
equipment, immediately turn the power off and unplug the power cord. Then, contact your service representative.
Precautions for Installation, Relocation, Storage and Connection
Do not install / store in any place other than specified
Do not place this product in any place other than the one shown below or specified by the server. It may cause a fire.
Dusty place
A humid place such as by the water heater
Place exposed to direct sunlight
Unstable place
Do not use the equipment in the place where corrosive gases exist.
Make sure not to locate or use the equipment in the place where corrosive gases (sulfur, dioxide, hydrogen sulfide, nitrogen
dioxide, chlorine, ammonia, ozone, etc.) exist.
Also, do not set it in the environment where the air (or dust) includes components accelerating corrosion (ex. sulfur, sodium
chloride) or conductive metals.
There is a risk of a fire due to corrosion and shorts of an internal printed board.
Contact your service representative for the place appropriate to the equipment.
Do not pull out with the interface cable
When disconnecting the cable, release the lock such as screws and hold the connector and pull it straight out. Holding the
cable by pulling it or applying excessive force to the connector may damage the cable and cause a fire or electric shock.
Do not use any unauthorized interface cable.
Use only interface cables authorized by NEC and locate a proper device and connector before connecting a cable. Using
an authorized cable or connecting a cable to an improper destination may cause a short circuit, resulting in a fire.
Also, observe the following notes on using and connecting an interface cable.
Do not use any damaged cable connector.
Do not step on the cable.
Do not put any object on the cable.
Do not use the card with the loose interface cable connection.
Do not use any damaged cable.
Fix the interface cable securely
When connecting a video cable, conversion connector, etc., be sure to lock the screw securely.
Poor contact may cause smoke or fire.
Do not pull out with the interface cable
When disconnecting the cable, release the lock such as screws and hold the connector and pull it straight out. Holding the
cable by pulling it or applying excessive force to the connector may damage the cable and cause a fire or electric shock.
Precautions for Handling of Internal Devices
Do not disassemble, repair, or modify the product yourself
Do not disassemble, repair, or modify this product. Doing so may cause an electrical shock or a fire. Do not put the product
close to fire, or immerse it in water. Doing so may cause an explosion. If the product does not function normally, contact
your service representative.
Avoid installation in extreme temperature conditions.
Immediately after the server is powered off, its internal components such as heat sink are very hot. Leave the server until
its internal components fully cool down before installing/removing any component.
Ground yourself to dissipate any static charge before handling the adapter.
To prevent any damage on components due to static electricity, make sure to discharge static electricity from yourself before
you touch N8105-61 adapter.
Don’t touch uncoated metal parts on adapter.
Never touch N8105-61 adapter’s mDP terminals of components or uncoated metal parts on adapter. Otherwise, taint,
erosion or others may cause loose connection. Do not touch this product with wet or dirty hands.
Excessive force could break the connector.
On installing this adapter, do not insert it by force. Otherwise, N8105-61 adapter and the server may be damaged.
Don’t touch the tip of bracket to other parts of server
When you insert N8105-61 adapter into expansion slot, be careful not to touch the tip of bracket to other parts of server
(such as other components or board). Otherwise, they may be damaged.
Stay away from the fan.
Keep your hand or hair away from the cooling fan on the adapter.
Failure to follow this warning may get your hand or hair caught in the fan, resulting in injury.
Don’t operate with dust on the front or inside of the device
Clean it regularly.
Continued operation with dust on the front or inside of the device may cause a fire. If you need to clean the inside of the
device, contact the store where you purchased the product or a maintenance service company.
Don’t attach or remove this product with the disinfectant attached to your fingers.
Don’t install or remove optional products with the disinfectant on your fingers. If the disinfectant adheres to the machine, it
may corrode and cause malfunction, smoke or fire.
