NEC Express5800/E120f-M Maintenance Manual Download Page 74

Page: 74 / 165

1. System BIOS

Express5800/E120f-M Maintenance Guide

Chapter 2 Useful Features

(6) USB Configuration submenu

From the

Advanced

menu, select

USB Configuration

and then press the <Enter> key to display the menu

screen shown below.

For details about the options, see the table below.

Option

Parameter

Descriptions

Device Reset Timeout

10 sec
[20 sec]
30 sec
40 sec

Specify the timeout period when Start Unit
command is issued to USB mass storage
device.

Controller Timeout

1 sec
5 sec
10 sec
[20 sec]

Specify the timeout period when Control, Bulk,
and Interrupt Transfer commands are issued
to USB Controller.

XHCI Mode

Smart Auto
[Auto]
Enabled
Disabled

Specify the operation mode of USB3.0
controller.

Smart Auto:

Takes over the USB3.0 settings

at POST according to support status of OS.

Auto:

Enables USB3.0 after the OS that

supports USB3.0 is started.

Enabled:

Enables USB3.0.

Disabled:

Disables USB3.0.

XHCI Hand-off

Disabled
[Enabled]

Enable or disable XHCI Hand-off feature.

[ ]: Factory setting

Summary of Contents for Express5800/E120f-M






































































































































































Search results

Summary of Contents for Express5800/E120f-M

Reviews:

Brands by name

Popular brands

NEC Express5800/E120f-M, Maintenance Manual

Search results

Summary of Contents for Express5800/E120f-M

Reviews:

Brands by name

Popular brands