NEC EdgeMarc 4500 Installation Manual Download Page 10

Page: 10 / 17

Getting Started

Physical Installation

The EdgeMarc 4500 is designed for desktop, rack or wall-mount installation. Observe the
following guidelines when installing the system:

•

Always verify that the AC cord is disconnected from a power source prior to installation.

•

Ensure that the installation site has adequate air circulation and meets the minimum

operating conditions for the system as specified in

Specifications

section of this document

Required Tools and Materials

•

If the unit is to be mounted on the wall then:

─

1 Flat or Philips screw driver

─

2 round or flat head Philips or slotted screws – 1

inch long

─

2 hollow wall anchors

•

If the unit will be mounted in a shelf:

─

1 Flat or Philips screw driver

•

Ethernet cables to connect the LAN ports to LAN switches or to individual IP phones. They

can also be used to connect the Ethernet WAN port to a WAN router, a Cable Modem or a
DSL Modem.

Desktop Installation

1. Remove the EdgeMarc 4500 and accessories from the shipping container.

2. Place the EdgeMarc 4500 on a flat, dry surface such as a desktop, shelf or tray.

Summary of Contents for EdgeMarc 4500


















Search results

Summary of Contents for EdgeMarc 4500

Reviews:

Related manuals for EdgeMarc 4500

Brands by name

Popular brands

NEC EdgeMarc 4500, Installation Manual

Search results

Summary of Contents for EdgeMarc 4500

Reviews:

Related manuals for EdgeMarc 4500

Brands by name

Popular brands