background image

Extron • System 4

xi

xi

xi

xi

xi

 Switcher Series • User’s Manual • P/N 68-413-02 Rev. E

Configuration and Connections

NEC Installation

Page 9

(Note: Information depends on
System 4

xi

 setup.)

(See note.)

(See note.)

(See note.)

(See note.)

[System 4

xi

 model and software

version displayed here]

Connecting System 4

xi

xi

xi

xi

xi

 to NEC GT 2000 (or equivalent) Projector

If the System 4

xi

 is already configured for an NEC GT 2000 projector, go to step

4. If it is not set up correctly, it will be necessary to change switch settings on the
System 4

xi 

’s Main Controller Board. Begin at Step 1 to verify the correct

configuration.

1. Use the Front Panel to display the Information Menu to verify that the System 4

xi

is already set up for the NEC GT 2000 projector. Apply power to the System 4

xi

and do the following:

a. Press 

 to display the M

ENU

 S

ELECT

 on the LCD screen.

b. Press 

 or 

 to step to Menu 8.

c. Press 

 to select this menu.

d. Press 

 or 

 to display the configuration. The example to the left is general,

yours will show the System 4

xi

 model name, the software version and the

following information:
PRJ = NEC_GT
PRJ BAUD = 9600
UNIT No. = 000
HST BAUD = 9600 (value depends upon setup Menu 3)

2. Go to the procedure on page 2-3 to remove the System 4

xi

 cover and then go to

page 2-4 to set up the Main Controller board. Return to Step 3 (below) when the
configuration is correct.

Config

Projector

SW1: 1-2-3-4 SW2

SW3

SW4

SW5

SW6

Prj Cable

Comm

as

Adapter

 NEC GT 2000

off-on-on-off

0

0

4

E

0

J15

26-494-01

3. Double-check your work and be sure the System 4

xi

 cover is on securely.

4. Install the System 4

xi

 in its place of operation (i.e. rack), but not powered on.

__________ Changes in some switch configurations are not detected until the power is

removed at the AC cord, and then restored.
If the Projector Cable is wrongly connected to J9 on the Main Controller Board,
Menu 8 will not indicate the error.

Use the following connection diagram and continue.

}

SW1

ON

SW2

SW4

SW3

SW5

J15

3

4

1

2

Summary of Contents for 4xi NEC













Reviews: