background image

Extron • System 4

xi

xi

xi

xi

xi

 Switcher Series • User’s Manual • P/N 68-413-02 Rev. E

Configuration and Connections

NEC Installation

6. Plug the 15-pin HD connector of the Projector Communications Extension cable

(shown as CC 50') into the PJ Comm port on the System 4

xi

. The other end has

a 9-pin female connector. Plug this into the other 9-pin male D connector on the
NC COM adapter.

______ Secure all of the connector screws.

7. Plug the (4 or 5) BNC connectors from one end of the (user-supplied) RGBS/HV

cable onto the System 4

xi

 output and those on the other end onto the matching

BNCs on the NEC connector panel. See cable diagram.

8. Power up the projector and set the projector as follows:

• if your system has less than 10 inputs, set the projector to SW_Level 1 mode

• if your system has 10 or more inputs, set the projector to SW_Level 2 mode

9. Apply AC power to the System 4

xi

.

____________ For the NEC XG: always apply AC power to the projector and place it in Stand-

NEC Memory Assignments

by power before applying AC power to the System 4

xi

.  This procedure must be

 

followed anytime AC power to the system has been interrupted or the CC cable

 

detached.  Failure to follow this AC power up sequence will cause
communication errors.

The following two examples and accompanying tables provide information for

 

setting up the NEC projector (not the System 4xi). Please refer to the projector

 

documentation for further details.

The table on the right lists the Extron channel assignments and the

 

corresponding NEC 

host and peripheral

 slot

assignments using Extron System Switchers.

The physical location of the Extron channel
assignments will depend on the system
setup.

The tables and charts in the examples below
illustrate System Switcher channel
assignments for NEC models PG, PG+, PGX
and XG.

__________ System 4xi can support a maximum of 22

channels: 1 System 4xi (

host

) looped to

 

multiple System 10 Switchers (

peripherals

).

Page 3

EXTRON
CHANNEL
NUMBER

NEC SLOT

ASSIGNMENT:

HOST

NEC SLOT

ASSIGNMENT:

PERIPHERALS

1
2
3
4

5
6
7
8
9

10
11
12
13
14

M01
M01
M01
M01
M01
M01
M01
M01
M01
M01
M02
M02
M02
M02
M02
M02
M02
M02
M02
M02
M03
M03
M03

15
16
17
18
19
20
21
22
23

S01
S02
S03
S04
S05
S06
S07
S08
S09
S10
S01
S02
S03
S04
S05
S06
S07
S08
S09
S10
S01
S02
S03

96

M10

S06

97
98
99
100

M10
M10
M10
M10

S07
S08
S09
S10

Summary of Contents for 4xi NEC













Reviews: