NEC 1090030 - DSX Systems PHONE SuperDisp Phone... Hardware Manual Download Page 52

Page: 52 / 82

Upgrading the System Software

◆

Installation

DSX-40 Hardware Manual

Upgrading the System Software

Upgrade System Software

To upgrade system software from a CompactFlash card:

Remove the IntraMail CompactFlash card (if installed), then insert the CompactFlash card containing the

system software into the Main Equipment Cabinet.

- Although advisable, backing up the site programming is not required.

Press and hold the

Reset Switch

on the cabinet.

When the LED on the cabinet goes out, release the

Reset Switch

- The LED initially lights green, yellow, and then blue. During the software load, the LED alternately

lights blue and

ashes green.

- The software takes about seven minutes to load.
- The system restarts after the load completes with all the initial site programming intact.

Once the system restarts:

- Remove the software upgrade CompactFlash card.
- Insert the IntraMail CompactFlash card.
- Reset the system.

Figure 28: Loading System Software from a CompactFlash Card

1093097 - 20

Summary of Contents for 1090030 - DSX Systems PHONE SuperDisp Phone...



















































































Search results

Summary of Contents for 1090030 - DSX Systems PHONE SuperDisp Phone...

Reviews:

Related manuals for 1090030 - DSX Systems PHONE SuperDisp Phone...

Brands by name

Popular brands

NEC 1090030 - DSX Systems PHONE SuperDisp Phone..., Hardware Manual

Search results

Summary of Contents for 1090030 - DSX Systems PHONE SuperDisp Phone...

Reviews:

Related manuals for 1090030 - DSX Systems PHONE SuperDisp Phone...

Brands by name

Popular brands