NComputing L300 User Manual Download Page 46

Page: 46 / 95

NComputing L-Series User Manual rev.05.07.12

Page

Host unreachable…

When the access device cannot connect to the host PC, this message appears.

•

Make sure the server connection list is configured correctly. See the section about configuring
the access device.

•

Make sure the vSpace Server software is installed on the host PC.

•

Make sure the host computer and access device are in the same subnet/local area network.

•

Make sure any firewall or anti-virus programs installed in the host computer or network
equipment are compatible with the vSpace Server software.

TS ERROR – INVALID OR NO SERIAL NUMBER!

This message appears when no serial number exists in the host computer. This message does not
indicate an error regarding the serial number of the access device.

Please see the section about product registration to register the vSpace Server software and the access
devices.

Summary of Contents for L300
































































































Search results

Summary of Contents for L300

Reviews:

Related manuals for L300

Brands by name

Popular brands

NComputing L300, User Manual

Search results

Summary of Contents for L300

Reviews:

Related manuals for L300

Brands by name

Popular brands