background image

OVERVIEW OF THE ELECTRONIC PARTS

NCM 

PARIS MAX 36V

Charging the battery outside the bike

1. Unfold the box first.

2. Take out the battery

3. Connect the charger to the battery.
4. Connect the charger to an AC outlet.
5. The charging procedure can be stopped at any time.
6. Disconnect the charger from the AC outlet first and then from the battery.
7. Reinstall the battery and make sure it is aligned correctly at the bottom.
8. Press down on the top of the battery until you notice a "click" to ensure that the battery is properly secured.

9. Remove the key.

10. Your NCM electric bike is ready to ride.

Charging the battery inside the bike

1. Connect the charger to the battery.
2. Connect the charger to an AC outlet.
3. The charging procedure can be stopped at any time.
4. Disconnect the charger from the AC outlet first and then from the battery.
5. Your NCM electric bike is ready to ride.

4.2.5 Use

Make sure to activate the battery by turning on the power button on the right side of the protector.
Turn on the display on the handlebar, select the desired level of support, and begin pedaling. You will notice that the engine starts as soon as you start 
moving the pedals.
The charging time will be around 4 hours at a time. Please do not charge the battery for more than 10 hours at a time (the battery will be fully charged 
much earlier).

A fall resulting in serious injury can occur if the following points are not observed:

1. Before setting off, hold the handlebar straight.

2. To get familiar with the feel of the bike and riding, start with the engine off (you can set the support level to 0 on the monitor) Do not start the engine until it is 
moving.

3. Do not use the pedals to begin moving until you have assumed a safe and comfortable sitting position.

4. When driving around a sharp curve or corner, apply the brake lightly to temporarily disable the engine and allow a safe turn.

The bike can be operated with and without the motor auxiliary drive bracket. An empty battery does NOT mean that your bike cannot be used again.

When using the motor for pedal assist, proceed as if you were riding a normal bicycle; press down on the pedals and the motor will start and the bike will 
accelerate further.

Support level

If the bike remains stopped with the display and auxiliary unit activated, it will turn off after approximately 10 minutes along with the battery capacity indicator.

During longer slopes, the engine can get so hot that the current is reduced through the temperature sensor inside, causing the engine support level to drop; 
the driver may need to increase the physical support of the pedal to maintain speed.

16

Summary of Contents for PARIS MAX 36V





































Reviews: