background image

Page 8 

Naxa Electronics

Connecting the Unit to 
Power

Plug one end of the power adapter into the Power In-
put jack, and then plug the other end into AC wall out-
let. Before switching on the unit, make sure that the 
voltage of your electricity supply is the same as that 
indicated on the rating label of the power adapter.

ѥ

ѥ

The included adapter accepts AC 
100-240V power.

Battery Backup

Battery  backup  will  preserve  the  current  time, 
alarm  settings,  and  stored  radio  stations  in  the 
case of power failure or interrupted AC power.

Insert two  UM-4  batteries  (AAA)  into the  battery 
compartment.  Be  sure to  observe the  proper  po-
larity (the “+” and “-” signs) as indicated inside the 
battery compartment.

Setting the Clock

While the system is in Standby mode (i.e., the radio 
is off):

1. 

Press and hold the PRESET/TIME SET button. 
The time will begin to flash on the display.

2.  Press the 

 button to adjust the hour; press 

the 

 button to adjust the minutes.

 •

Hours and minutes run forward only 
when being set; if you pass the desired 
time, continue pressing the button until 
the time cycles back around.

3.  When the correct time is set, press the 

PRESET/

TIME SET

 button again to confirm.

ѥ

L

Take note of the PM LED indicator 
when setting the clock. 

Summary of Contents for NRC-180

















Reviews: