background image

7

8

   5. EJECT KEY

       In the power on state, the loaded disc can be ejected by pressing the EJ key.

 

  6. USB SOCKET

       

When needing to play the file in the USB stick, turn over the plastic cover cap then insert

       the USB stick into the USB socket. The system will change into the USB mode
       automatically, and then play the first file in the USB.

 

       

When no needing to do USB operation, please cover the plastic cover cap.

   7. SD CARD SLOT

       When you need to play the file in the SD card, insert the SD card into the card slot. 
       The system will change into the SD mode automatically, and then play the first file in the SD. 
       

Blue Tooth Handfree System:

1. Pairing
    Turn on the Bluetooth mode of the mobile phone, then select the item of Finding the 
    Bluetooth Device and enter it. After finishing the finding, it will show the name of the 
    Bluetooth Device if finding a Bluetooth Device. Select it and enter it, then it will show 
    a interface that ask you to input a password. Input the password 0000 and enter it. 
    Then it will tell you that pair OK and then connection OK, and the LCD of the car audio 
    system will show BT READY and then show the name of the Bluetooth Device of the 
    mobile phone.

2. Connection or disconnection
  A) Use the mobile phone to do connection or disconnection
    1) In the connection status, find the paired and connected Bluetooth Device, then press the
        disconnection button to do disconnection.
    2) In the disconnection status, find the paired and disconnected Bluetooth Device, then 
        press the connection button to do connection.
  B)  When turn on the power again(after Acc off ), the front panel can search the phone have
        pair automatically and be connection. And it will take you about 20 seconds.
Note:
 (1) The Bluetooth LED indicator on the front panel indicates the three connection status:
      

-

LED Turn off:  No connection at all

      

-

LED Blinking: Connection status

      -LED Turn on: Talking status
 (2) Bluetooth icon appears on LCD only when in connection status.
 (3) In the connection status: Mobile phone transfers to the car audio whenever a dialling 
       takes place; Mobile phone transfers to the car audio whenever receiving a call.

3. Dialling when in connection status

 

  

A) Dial with the mobile phone directly.

  B) Dial with remote control with the following procedures:
    1)  Press the TEL button, then CALL will appear on LCD.
    2)  Input telephone number with number buttons 0-9.
    3)  Press the CLEAR button to cancel the call if necessary.
    4)  Press and hold the CLEAR button to cancel all the input numbers if necessary.
    5)  Press TEL to execute the dialling. The talking time will appear on LCD if dialling 
          is successful and it is received.
  C) Redial
    1)  Press TEL button twice, it will show the last dialled phone number on LCD.
         Press TEL button once again, it will dial the number directly.
    2)  Press T-M button and the LCD will display the last in and last out number.
         Press TEL button to dial with the number.
Note: the phone number are numbers you have dialed and the call you have received.

Summary of Contents for NCA-692









Reviews: