NavLinkz VL3-MIB-STD2 Manual Download Page 1

Page: 1 / 21

Version 13.10.2017

HW: 25GD(v60)

VL3-MIB-STD2

v.LiNK

Video-inserter

VL3-MIB-STD2

Compatible with VW vehicles

with Composition Media or Discover Media system

Skoda vehicles with Amundsen or Bolero system

Seat vehicles with Media system plus

Video-inserter with 2 video + rear-view camera input and CAN control

Product features



Video-inserter for factory infotainment monitors



2 CVBS video-inputs for after-market devices (e.g. DVD-Player, DVB-T tuner, …)



Rear-view camera video-input



Automatic switching to rear-view camera input on engagement of reverse gear



Activatable parking guide lines for the rear-view camera (vehicle specific
restrictions possible)



Video-in-motion in drive mode (ONLY for connected video-sources)



Compatible with factory rear-view camera



AV-inputs only NTSC compatible

Summary of Contents for VL3-MIB-STD2






















Search results

Summary of Contents for VL3-MIB-STD2

Reviews:

Related manuals for VL3-MIB-STD2

Brands by name

Popular brands

NavLinkz VL3-MIB-STD2, Manual

Search results

Summary of Contents for VL3-MIB-STD2

Reviews:

Related manuals for VL3-MIB-STD2

Brands by name

Popular brands