background image

 

 

 

Version 20.08.2020 

HW: CAM(V100)/(V20) 

RL4-MIB92 

P

a

g

e

22

 

 
3.2.

 

By keypad 

 
Alternatively or additionally to the factory infotainment buttons, the interface’s external 
keypad can be used to switch the enabled inputs. Even if not needed, the keypad should 
always remain connected to the video interface for support purposes. 

 

 

Long press of keypad (2-3 seconds) 

 

By long pressing the external keypad (2-3 seconds), the video interfaces witches the input 
from the factory video to the inserted video sources. Each long press will switch to the next 
enabled input. Inputs which are not enabled will be skipped. 

 

Note: The interface switches after releasing the switch (after long pressure). 
 

 

Short press of keypad (only if DIP 1 is set to ON) 

 

By short pressing the external keypad, the video interfaces witches from the factory video to 
the front camera input and back to factory video. 
 
 

4.

 

Specifications 

 
BATT/ACC range 

 

 

 

 

7V - 25V 

Stand-by power drain  

 

 

 

7mA 

Power   

 

 

 

 

 

300mA @12V 

Video input   

 

 

 

 

0.7V - 1V  

Video input formats   

 

 

 

NTSC and PAL 

Temperature range   

 

 

 

-40°C to +85°C 

Dimensions video-box 

 

 

 

116 x 25 x 100 mm (W x H x D) 

 

 

Summary of Contents for RL4-MIB92

























Reviews: