manualshive.com logo in svg

Navia PN6280, User Manual, Page: 21 / 40

Share
Download
Navia PN6280 User Manual Download Page 21

 

                  PN6280_Hardware Design                           

 

Copyright © JSC NIIMA PROGRESS and NAVIA LLC                                                                                                                     
20 

 

3.5 IIC Interface

 

PN6280  module  does  not  have  a  dedicated  IIC  interface.  If  you  need  to  use  the  IIC  interface  for 

communication, you should use the GPIO port to simulate the IIC interface, and it is recommended to 

use an external pull-up resistor of 4.7K by VIO18. 

3.6 UART Interface

   

3.6.1

 

Pin description 

The module PN6280 provides two UART serial communication interfaces:   

the UART1 is as the end of the AP module debug port, 2-wire UART interface;   

UART0 can be debug port and also can be as complete non-synchronous communication interface, 

supporting standard modem handshake signal control and in compliance with the RS-232 interface 

protocol, also supporting 4-wire serial bus interface or 2-wire serial bus interface mode. The module 

can communicate AT commands by UART interfaces. 

The  two  groups  of  UART  ports  support  programmable  data  width,  stop  bits,  and  parity  bits,  with 

separate TX and Rx FIFOs (512 bytes each). The max baud rate of normal application of UART (non-

Bluetooth) is 115200bps. The default baud rate is 115200bps. 

Table 3-2    UART Pin Description 

Pin NO. 

Pin Name 

I/O 

Function Description 

18 

URXD1 

DI 

UART1 receive data input only for debugging 

19 

UTXD1 

DO 

UART1 transmit output only for debugging 

50 

UART0_RTS 

DI 

UART0 Ready to receive 

51 

UART0_CTS 

DO 

UART0 Clear to Send 

Summary of Contents for PN6280









































Reviews:

No comments