background image

BHM 

10/04/18 

NTV-DOC266  

 

 

Agreement

End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product.  

If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road use and passenger 

entertainment only.  

16 | 

P a g e

 

 

FAQs 

Q1. I can’t get into programming mode.

 

 

A1. Turn off the vehicle and remove the key. Close all points of entry and use the remote to lock the vehicle. 

Wait approx. 5 minutes without opening or disturbing the vehicle. Unlock and cycle the ignition to the ‘RUN’ position. 

Make certain that the cluster is in FM radio mode before you begin programming;

 and no errors are displayed (door 

open, etc), otherwise the cluster information might not display. Hold down the “MUTE” button until you see the display 

options post on the cluster. 

Q2. When I try to force (front, rear) camera, nothing happens.  

A2. Make certain you’ve enabled the options you want to u

se in the NAVTV settings mode and that you scrolled 

to the end 

and selected ‘EXIT’ (or it will not save)

.  

Q3. I hear no audio when my auxiliary source is playing on screen.  

 A3. Verify that the audio RCAs are connected properly to the AVSW.  

Q4. Everything works properly, but when an audio source is connected to the 3.5mm audio jack, 

there’s no audio. 

 

 A4. Make sure the audio RCAs are connected together on the Plug & Play harness.  

Q5. When I place the vehicle into reverse, I get a black or blue screen.  

A5. Make sure the camera is getting sufficient power and the RCA is connected to the proper yellow RCA on the 

24-pin harness.  

Q6. The camera image is displayed properly when the vehicle is in rev

erse, but there’s only a black or blue 

screen 

when the camera is forced.  

A6. Make sure the camera power is not connected to the reverse lamps. Camera power needs to be connected 

to an accessory wire (cigarette lighter). If the camera is OEM, forcing it to display in any gear is 

not

 supported.  

Other MULTI-CAM Notes: 

 

When multiple cameras are connected, the MULTI-CAM will clear back to the factory image 

after 3 cameras 

have been forced in succession. This is normal. 

I.E: If you had AUX mode displayed on screen, turned the left 

turn signal on (which will display), then rolled up to an obstacle which forced the front camera, placing the 
vehicle into park will then display the factory image 

(will not return to AUX image automatically). 

 

 

Cluster feedback only displays while programming (NAVTV Settings).  

 

Cargo Camera usage will only display for about 8 seconds when in motion, then will time out (this is a factory 
limitation). Activating the CIM feature will retain this image for 3 minutes if desired. 

 

When setting Cargo Cam to ‘ON’ or ‘FIX’, you must let the vehicle perform a full CAN reset, after programming, 

before the menu will display properly.  

 

 

 

 

Summary of Contents for CHRY MULTI-CAM


















Reviews: