Fig.7
Press here to release and pull to disconnect
Fig.8
Charging the Battery
For battery charging follow these instructions.
1. Always ensure that the Master Switch is Off - see figure 3.
2. Always ensure that the SEASCOOTER™ is out of the water, dry and placed in a dry area.
3. Give a half turn to the Latches and remove them from the Nose Cone as shown in figure 5.
4. Remove the Outer Nose Cone and Buoyancy Control Chamber.
5. Open the Vent by unscrewing the Vent Plug.
6. Remove the Inner Nose Cone. To do this, first feed the Silicone Ring (provided with this
manual) through the latch holes in the Inner Nose Cone and pull over the hooks on the Battery
Housing (see figure 7). Then screw the Pump Nozzle onto the Vent Hole and pump air into the
Battery Chamber until the Inner Nose Cone pops off and then remove the Silicone Ring.
7. Allow two minutes for any gases to dissipate.
8. Disconnect the battery cable from the housing cable (if not already disconnected - the cable
will be disconnected when you buy your SEASCOOTER™) by pressing the locking feature, as
shown in figure 8.
9. Remove the battery and place on a level surface.
10. Connect the battery cable to the charger cable.
11. Plug charger into mains, and turn on the supply.
15. Unplug the battery cable from the Charger cable.
16. When ready for use, install the battery and reconnect to the housing cable.
21. Replace the Buoyancy Control Chamber.
22. Replace the Outer Nose Cone making sure the key is aligned correctly and
insert the Latches and lock the Nose Cone by giving them a half turn. See
fig.12.
1. Remove the SEASCOOTER™ from the water.
2. Make sure the master switch is off.
3. Remove the battery - see page 16, step 1-9.
9. Replace the washer(s) and nut and tighten with the socket
while holding the Propeller making sure it is securely
fastened (See figure 20).
10. Replace the grille.
11. Replace the battery.
6. Slide the Propeller off the shaft, taking care not to loose the
drive pin or washers.
7. Remove the blockage from the Propeller.
8. Replace the drive pin (if removed), see figure 19, and Propeller.
Turn the Propeller slowly until you locate the pin and push
the Propeller fully on.
17. Make sure the seals and sealing surfaces are clean and fully lubricated with the
supplied grease EVERYTIME (you can also buy this at your local hardware store)
before replacing the Inner Nose Cone. See fig. 9.
18. Replace the Inner Nose Cone making sure the key is aligned correctly. See fig. 10.
19. Ensure the Vent O Ring is fitted correctly and fully lubricated with the supplied grease
EVERYTIME (you can also buy this at your local hardware store). See fig. 11.
20. Screw in the Vent Plug to seal the vent.
12.
SEASCOOTER MARINE 200
- Charging will take 3 - 4 hours for a fully
discharged battery.
SEASCOOTER MARINE 250 / MARINE 280 / MARINE 300
- Charging will
take 5 - 7 hours for a fully discharged battery.
When the battery is charging the red LED is lit, when the battery is charged
the green LED is lit.
13. Disconnect the charger from the electrical plug/socket.
14. Allow battery to stand for 30 minutes before using it.
Important Notice: Keep the Silicone Ring permanently
(Refer to Page 2 and 3, Parts Diagram). Removing the
inner nose cone without the Silicone Ring is dangerous.
17
16
4. Unscrew the six rear grille screws as shown in figure 17.
5. While holding the Propeller, use an M6 socket to remove the
nut from the Propeller shaft (See figure 18).
Replace the battery immediately if it is damaged.
- The instructions concerning persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge and children playing with the
appliance are not applicable.
- The connector must be removed before the appliance is cleaned and that the appliance inlet
must be dried before the appliance is used again.
- Detachable power supply part shall be provided with the part of class III construction of the
appliance.
- The transformers or battery chargers used with the product are to be regularly examined for
damage to the cord, plug, enclosure and other parts, and in the event of such damage, they
must not to be used until the damage has been repaired.
WARNING
