background image

These  Evaluation  Boards  are  intended  for  product  evaluation  purposes  only  and  are  not  intended  for  resale  to  end

consumers, is not authorized for such use and is not designed for compliance with European EMC Directive 89/336/EEC.

National does not assume any responsibility for use of any circuitry or software supplied or described. No circuit patent

licenses are implied.

LIFE SUPPORT POLICY

NATIONAL'S  PRODUCTS  ARE  NOT  AUTHORIZED  FOR  USE  AS  CRITICAL  COMPONENTS  IN  LIFE  SUPPORT

DEVICES  OR  SYSTEMS  WITHOUT  THE  EXPRESS  WRITTEN  APPROVAL  OF  THE  PRESIDENT  OF  NATIONAL

SEMICONDUCTOR CORPORATION. As used herein:
1. Life  support  devices  or  systems  are  devices  or

systems which, (a) are intended for surgical implant

into  the  body,  or  (b)  support  or  sustain  life,  and

whose  failure  to  perform,  when  properly  used  in

accordance with instructions for use provided in the

labeling, can be reasonably expected to result in a

significant injury to the user.

2. A  critical  component  is  any  component  in  a  life

support device or  system  whose  failure  to  perform

can be reasonably expected to cause the failure of

the  life  support  device  or  system,  or  to  affect  its

safety or effectiveness.

National Semiconductor Corporation

Americas

Tel:      1-800-272-9959

Fax:     1-800-737-7018

Email: [email protected]

National Semiconductor Europe

Fax: +49 (0) 1 80-530 85 86

Email: [email protected]

Deutsch Tel: +49 (0) 1 80-530 85 85

English   Tel: +49 (0) 1 80 532 78 32

Français Tel: +49 (0) 1 80 532 93 58

Italiano   Tel: +49 (0) 1 80 534 16 8

National Semiconductor

Asia Pacific Customer

Response Group

Tel:  65-2544466

Fax: 65-2504466

Email: [email protected]

National Semiconductor

Japan Ltd.

Tel:   81-3-5620-6175

Fax:  81-3-5620-6179

www.national.com

National does not assume any responsibility for any circuitry described, no circuit patent licenses are implied and National reserves the right

at any time without notice to change said circuitry and specifications.

              

12

          

http://www.national.com

Summary of Contents for ADC122S101














Reviews: