background image

©

 National Instruments

15

SCXI-1102/B/C Calibration Procedure

Gain and Offset

Table 6 contains the test limits to use when verifying and adjusting the gain 
and offset of the SCXI-1102 and SCXI-1102B. Table 7 contains the test 
limits to use when verifying and adjusting the gain and offset of the 
SCXI-1102C. If the SCXI-1102/B/C was calibrated within the last year, the 
test point value should fall between the Lower Limit and Upper Limit 
values found in Tables 6 or 7.

Note

The values in Tables 6 and 7 do not include DAQ device errors.

SCXI-1102/B/C Front and Rear Panel Diagrams

Table 8 shows the pin assignments for the SCXI-1102/B/C front panel 
connector. Table 9 shows the pin assignments for the SCXI-1102/B/C rear 
signal connector.

Table 6.  

SCXI-1102 and SCXI-1102 B Test Limits

Gain

Test Point (V)

Upper Limit (V)

Lower Limit (V)

1

9.800000

9.80345

9.79655

0.000000

0.001002

-0.001002

–9.800000

–9.79655

–9.80345

100

0.098000

0.098060

0.097940

0.000000

0.000030

–0.000030

–0.098000

–0.097940

–0.098060

Table 7.  

SCXI-1102 C Test Limits

Gain

Test Point (V)

Upper Limit (V)

Lower Limit (V)

1

9.800000

9.80345

9.79655

0.000000

0.001002

-0.001002

–9.800000

–9.79655

–9.80345

100

0.098000

0.098060

0.097940

0.000000

0.000030

–0.000030

–0.098000

–0.097940

–0.098060

Summary of Contents for SCXI SCXI-1102



















Reviews: