background image

Legal Information

Limited Warranty

This document is provided ‘as is’ and is subject to being changed, without notice, in future editions. For the latest version, 

refer to 

ni.com/manuals

. NI reviews this document carefully for technical accuracy; however, NI MAKES NO EXPRESS 

OR IMPLIED WARRANTIES AS TO THE ACCURACY OF THE INFORMATION CONTAINED HEREIN AND 

SHALL NOT BE LIABLE FOR ANY ERRORS.
NI warrants that its hardware products will be free of defects in materials and workmanship that cause the product to fail to 

substantially conform to the applicable NI published specifications for one (1) year from the date of invoice.
For a period of ninety (90) days from the date of invoice, NI warrants that (i) its software products will perform substantially 

in accordance with the applicable documentation provided with the software and (ii) the software media will be free from 

defects in materials and workmanship.
If NI receives notice of a defect or non-conformance during the applicable warranty period, NI will, in its discretion: (i) repair 

or replace the affected product, or (ii) refund the fees paid for the affected product. Repaired or replaced Hardware will be 

warranted for the remainder of the original warranty period or ninety (90) days, whichever is longer. If NI elects to repair or 

replace the product, NI may use new or refurbished parts or products that are equivalent to new in performance and reliability 

and are at least functionally equivalent to the original part or product.
You must obtain an RMA number from NI before returning any product to NI. NI reserves the right to charge a fee for 

examining and testing Hardware not covered by the Limited Warranty.
This Limited Warranty does not apply if the defect of the product resulted from improper or inadequate maintenance, 

installation, repair, or calibration (performed by a party other than NI); unauthorized modification; improper environment; 

use of an improper hardware or software key; improper use or operation outside of the specification for the product; improper 

voltages; accident, abuse, or neglect; or a hazard such as lightning, flood, or other act of nature.
THE REMEDIES SET FORTH ABOVE ARE EXCLUSIVE AND THE CUSTOMER’S SOLE REMEDIES, AND SHALL 

APPLY EVEN IF SUCH REMEDIES FAIL OF THEIR ESSENTIAL PURPOSE.
EXCEPT AS EXPRESSLY SET FORTH HEREIN, PRODUCTS ARE PROVIDED "AS IS" WITHOUT WARRANTY OF 

ANY KIND AND NI DISCLAIMS ALL WARRANTIES, EXPRESSED OR IMPLIED, WITH RESPECT TO THE 

PRODUCTS, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A 

PARTICULAR PURPOSE, TITLE OR NON-INFRINGEMENT, AND ANY WARRANTIES THAT MAY ARISE FROM 

USAGE OF TRADE OR COURSE OF DEALING. NI DOES NOT WARRANT, GUARANTEE, OR MAKE ANY 

REPRESENTATIONS REGARDING THE USE OF OR THE RESULTS OF THE USE OF THE PRODUCTS IN TERMS 

OF CORRECTNESS, ACCURACY, RELIABILITY, OR OTHERWISE. NI DOES NOT WARRANT THAT THE 

OPERATION OF THE PRODUCTS WILL BE UNINTERRUPTED OR ERROR FREE.
In the event that you and NI have a separate signed written agreement with warranty terms covering the products, then the 

warranty terms in the separate agreement shall control.

Copyright

Under the copyright laws, this publication may not be reproduced or transmitted in any form, electronic or mechanical, 

including photocopying, recording, storing in an information retrieval system, or translating, in whole or in part, without the 

prior written consent of National Instruments Corporation.
National Instruments respects the intellectual property of others, and we ask our users to do the same. NI software is protected 

by copyright and other intellectual property laws. Where NI software may be used to reproduce software or other materials 

belonging to others, you may use NI software only to reproduce materials that you may reproduce in accordance with the 

terms of any applicable license or other legal restriction.

End-User License Agreements and Third-Party Legal Notices

You can find end-user license agreements (EULAs) and third-party legal notices in the following locations:

Notices are located in the 

<National Instruments>\_Legal Information

 and 

<National Instruments>

 

directories.

EULAs are located in the 

<National Instruments>\Shared\MDF\Legal\license

 directory.

Review 

<National Instruments>\_Legal Information.txt

 for information on including legal information in 

installers built with NI products.

U.S. Government Restricted Rights

If you are an agency, department, or other entity of the United States Government (“Government”), the use, duplication, 

reproduction, release, modification, disclosure or transfer of the technical data included in this manual is governed by the 

Restricted Rights provisions under Federal Acquisition Regulation 52.227-14 for civilian agencies and Defense Federal 

Acquisition Regulation Supplement Section 252.227-7014 and 252.227-7015 for military agencies.

Trademarks

Refer to the 

NI Trademarks and Logo Guidelines

 at 

ni.com/trademarks

 for more information on National Instruments 

trademarks.
ARM, Keil, and µVision are trademarks or registered of ARM Ltd or its subsidiaries.
LEGO, the LEGO logo, WEDO, and MINDSTORMS are trademarks of the LEGO Group.
TETRIX by Pitsco is a trademark of Pitsco, Inc.
FIELDBUS FOUNDATION

 and FOUNDATION

 are trademarks of the Fieldbus Foundation.

Summary of Contents for SC Express Series





































Reviews: